background image

6

S

ection

 2 — i

mportant

 S

afe

 o

peration

 p

racticeS

Safety Symbols

This page depicts and describes safety symbols that may appear on this product.  Read, understand, and follow all instructions on the 

machine before attempting to assemble and operate.

Symbol

Description

READ THE OPERATOR’S MANUAL(S)

 

Read, understand, and follow all instructions in the manual(s) before attempting to 

assemble and operate

WARNING — CRUSHING HAZARD

 

Keep hands away from wedge, end plate, partially split wood and moving parts.

BYSTANDERS

 

Keep bystanders, helpers and children at least 10 feet away.

SINGLE OPERATOR

 

Only one person should operate the machine at a time. The adult who loads and stabilizes the 

log must be the person who operates control handle.

WARNING — PRESSURIZED FLUID

 

Never check for hose leaks with your hands. High pressure fluid can escape through a pin hole 

leak and cause serious injury by puncturing the skin and causing blood poisoning.

EYE PROTECTION

 

Always wear safety glasses or safety goggles when operating this machine.

WARNING — MOVING WEDGE

 

Keep hands away from wedge and moving parts.

WARNING—GASOLINE IS FLAMMABLE

 

Allow the engine to cool at least two minutes before refueling.

WARNING— CARBON MONOXIDE

Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon 

monoxide, an odorless and deadly gas.

WARNING— HOT SURFACE

 

Engine parts, especially the muffler, become extremely hot during operation. Allow engine 

and muffler to cool before touching.

WARNING!

 

Your Responsibility — Restrict the use of this power machine to persons who read, understand and 

follow the warnings and instructions in this manual and on the machine. 

SAVE THESE INSTRUCTIONS!

Summary of Contents for RM 33 LS

























Reviews: