background image

8. Securing the floor and inner roof centre piece

Secure each floor panel down using 6 x 60mm screws as shown, fix the centre piece of the floor using 2 x 60mm screw. Inside the roof of the gazebo secure to the bottom
of the roof centre block the hexagonal inner roof centre, ensure it is central to the block and fix in place using 2 x 60mm screws.

60mm

60mm

60mm

60mm

60mm

60mm

9. Floor edges and corner finials

Around the base of the gazebo attach the floor edges between the posts, ensure the top edge is flush with the floor and secure using 3 x 40mm screws per edge, screw
through the edge strip into the end of the floor panels. Choose the side which is to be the front or entrance to the gazebo. In the corners between the upright posts and
the top frames of the chosen side secure the 2 corner finial using 2 x 40mm screws per finial, screw through the finial into the upright posts.

40mm

40mm

Note:

Corner finials are fitted

to the side of the gazebo

that is to be the front or

entrance.

Drill

Drill 4mm pilot holes

in the panel frames for
each screw in this
section.

40mm

10. Infill panels

Before starting this section please see the infill panel variations on the last page.This section explains how to attach the panels in the first combination.
On either side of the gazebo entrance position a Lattice infill panel between the post with the bottom resting on the floor. Secure in place using 4 x60mm screws, screw
through the lattice frame into the upright posts. fix a hand rail to each of these panels, ensure the rebate in the hand rail is fitted over the lattice panel attach using
3 x 40mm screws per rail. Screw up through the lattice frame into the hand rail. Opposite the entrance fit between the upright posts the back infill panel. Secure into place
using 6x60mm screws, screw through the framing of the panel into the uprights For the remaining 2 gaps either side of the back panel fit a solid half infill panel at the
bottom and a lattice piece at the top using 4 x 60mm screws per panel, secure through the framing of the panels into the upright legs.

entrance to gazebo 

Summary of Contents for Gainsborough Gazebo






Reviews: