background image

R-CAST SERIES WALL FURNACE

12-99                                                                                             27                                                                                         30750B

LIMITED LIFETIME WARRANTY

ROYAL GAS FIREPLACE PRODUCTS

A. BASIC ONE-YEAR WARRANTY.  HEARTH TECHNOLOGIES INC., located at 20802 Kensington Boulevard, Lakeville,
MN 55044, (“HEARTH”) warrants to the original owner that your new ROYAL Gas Fireplace (the “Product”) will be free from
defects in materials and workmanship for a period of one year from the date of installation. During the first year, HEARTH will
replace or repair, at its discretion, any defective components (not limited to steel and cast iron components) at its sole cost
and expense, including payment of all reasonable labor costs incurred in replacing or repairing such components. This basic
warranty is subject to the conditions, exclusions and limitations described below.
B. EXTENDED LIFETIME COVERAGE. HEARTH warrants that the firebox, heat exchanger, log(s), and burner will not be
defective
in material or workmanship during the period the Product is owned by the original owner, subject to the following conditions
and limitations:
1. The ROYAL Gas Fireplace must have been installed and operated in compliance with the instructions in the installer’s

guide and user’s manual furnished with the Product. Any failure to properly install or operate the Product will void this
warranty.

2. This warranty applies to the original owner only and is non-transferable.
3. This warranty applies only to Products installed in the United States of America or Canada.
4. This warranty is limited to the replacement or repair of defective components or workmanship and HEARTH may fully

discharge all obligations under this warranty by repairing or replacing, at its discretion, the defective components. The
maximum amount recoverable under this warranty is limited to the purchase price of the Product and, if HEARTH is
unable to provide replacement or repair in an expedient and cost-effective manner, HEARTH may discharge all obliga-
tions under this warranty by refunding the purchase price of the Product. IN NO EVENT SHALL HEARTH BE LIABLE
FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY DEFECTS IN THE PRODUCT.

5. Any labor and related repair charges relating to the costs and expenses of replacing or repairing defective components

under the Limited Lifetime Warranty are not covered by this warranty.

6. Components and parts made by other manufacturers, whether sold with the Product or added thereafter, are NOT covered

by this warranty.

7. This warranty will be void if:

a) Any parts or components made by other manufacturers are added or used in the Product.
b) The Product is not installed in compliance with the instructions in the installerís guide. 
c) The Product is not operated, at all times, according to the userís manual furnished with the Product.
d) Any service work is performed on the Product by anyone other than an authorized HEARTH representative.
e) The Product is subjected to any alteration, abuse, accident or misuse.

EXCEPT TO THE EXTENT PROVIDED BY LAW, HEARTH MAKES NO EXPRESS WARRANTIES OTHER THAN
THE WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO THE
DURATION OF THE WARRANTY SPECIFIED ABOVE.

Some states do not allow limitations on how long an implied warranty lasts, or do not allow exclusion or limitation of incidental
or consequential damages, so those limitations may not apply to you. This warranty gives you specific legal rights, and you
may also have other rights which vary from State to State.
If warranty service is needed you should contact your installing dealer and if the installing dealer is unable to provide neces-
sary parts or components, contact the nearest authorized HEARTH dealer or supplier.
NOTES TO CUSTOMER:
1. In order to insure proper installation, operation and maintenance HEARTH strongly recommends annual servicing by an

authorized HEARTH dealer.

2. Please complete this information and retain this warranty in a safe place for future reference:

Model Number: ____________________________________________________________
Serial Number: _____________________________________________________________
Installation Date: ___________________________________________________________
Installing Contractor: ________________________________________________________

3. HEARTH reserves the right to make changes at any time, without notice, in design, material, specifications and prices of

the Product.  HEARTH also reserves the right to discontinue styles and products.

Summary of Contents for R-CAST



























Reviews: