background image

28

PX4 AIR

®

LIMITED WARRANTY

RPB

®

 warrants that its Products will be free from defects in materials and workmanship for one (1) 

year, subject to the terms of this limited warranty.  The Products are sold only for commercial use, 
and no consumer warranties apply to the Products. This limited warranty is for the benefit of the 
original Product purchaser, and cannot be transferred or assigned. This is the sole and exclusive 
warranty provided by RPB

®

, and ALL CONDITIONS AND IMPLIED WARRANTIES (INCLUDING 

ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) 
ARE EXCLUDED AND DISCLAIMED FROM WARRANTY COVERAGE.  RPB’s

®

 limited warranty 

coverage does not apply to damage resulting from accident, improper use or misuse of the 
Products, wear and tear resulting from the normal use of the Products, or the failure to properly 
maintain the Products.

RPB’s

®

 limited warranty coverage runs from the original date of purchase of the Products, and 

applies only to warranted defects which first manifest themselves and are reported to RPB

®

 within 

the warranty period.  RPB

®

 retains the right to determine to its reasonable satisfaction whether 

any claimed defect is covered by this limited warranty.

If a warranted defect occurs, RPB

®

 will repair or replace the defective Product (or a component 

of the Product), in its sole discretion.  This “repair or replacement” remedy is the sole and 
exclusive remedy under this limited warranty, and under no circumstances shall RPB’s

®

 liability 

under this limited warranty exceed the original purchase price for the Products (or the applicable 
component). RPB

®

 has no responsibility for incidental or consequential damages, including loss 

of use, maintenance and other costs, and ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES 
ARE EXCLUDED AND DISCLAIMED from this limited warranty.  Contact RPB

®

 to obtain warranty 

service. Proof of purchase must be provided to obtain warranty service.  All costs of returning the 
Products to RPB

®

 for warranty service must be paid by the purchaser.

RPB

®

 reserves the right to improve its Products through changes in design or materials without 

being obligated to purchasers of previously manufactured Products.

LIABILITY

RPB

®

 Safety cannot accept any liability of whatsoever nature arising directly or indirectly from 

the use or misuse of RPB

®

 Safety products, including purposes that the products are not designed 

for. RPB

®

 Safety is not liable for damage, loss or expense resulting from the failure to give advice 

or information or the giving of incorrect advice or information, whether or not due to RPB

®

 

Safety’s negligence or that of its employees, agents or subcontractors.

Summary of Contents for NIOSH PX4 AIR































Reviews: