background image

M

AGNUM

-OP-EN 

- 5 -

WARNING

The Batteries in this machine produce hazardous 
voltage which can cause electrical shock, burns and/
or electrocution. Always disconnect Batteries before 
servicing this machine.

WARNING

When climbing or descending ramps, always drive 
machine forward. To avoid overturning the machine, Do 
not back down ramps. Do not drive across inclines. Do 
not turn while ascending or descending ramps. Over-
turning the machine can cause serious injury or death.

WARNING

Do not use water that exceeds 135

°

F / 57

°

C.  If wa-

ter is above said temperature, this will void the Tank 
Warranty.

WARNING

Do not park this machine on ramps or slopes. Always 
park this machine on a level, hard surface. Do not oper-
ate this machine outdoors or on uneven surfaces.

WARNING

The Batteries in this machine contain sulfuric acid, 
which causes burns to skin. If battery acid contacts 
clothing or skin, rinse the effected area with cold water 
immediately. If battery acid gets on your face or in your 
eyes, fl ush the area immediately with cold water and 
seek medical attention.

WARNING

To avoid electrical shock, do not operate this machine 
over electrical fl oor outlets.

WARNING

Dress safely. Do not wear rings or metal wrist watches 
when servicing this machine, as they can cause an 
electrical short circuit which can cause serious burns.

WARNING

Do not remove, paint over or destroy warning decals. If 
warning decals become damaged, call 1-262-681-3583 
for free replacements.

WARNING

Dress safely. Do not wear a neck tie, scarf, or any 
loose or dangling clothing while operating this machine. 
Loose or dangling clothing or neck-wear can tangle in 
rotating parts, causing serious injury or death.

WARNING

Always turn off this machine before leaving it unat-
tended. Do not allow untrained persons to operate this 
machine.

WARNING

NO RIDERS. Do not carry passengers on this ma-
chine. Do not use this machine as a stepladder or work 
platform.

WARNING

Understand the dynamic braking system before you 
operate the machine on ramps.  Machine may coast.

WARNING

Before you service a Battery, always wear face protec-

tion, protective gloves and protective clothing.  Battery 

acid or battery explosion can cause serious injuries.

CAUTION

To avoid damage to this machine, use only cleaning 
solutions and replacement parts recommended by the 
manufacturer.

CAUTION

Do not operate this machine if any parts have been 
damaged or removed.

CAUTION

Always use the automatic battery charger provided by 
the manufacturer of this machine to charge the Batter-
ies of this machine. It is designed to charge the Batter-
ies at the appropriate rate. If you must use a different 
charger, disconnect the Batteries before charging to 
avoid damage to the electronic speed controller.

CAUTION

To avoid damage to the electronic control components 
of this machine, Do not store this machine outdoors. Do 
not pressure wash this machine.

Summary of Contents for Magnum 26" Disk











































Reviews: