background image

Heavy Duty True RMS Digital Multimeter/English

Heavy Duty True RMS Digital Multimeter/English

7

6

13/08/2017 Version No. 001

13/08/2017 Version No. 001

otar

    Select a primary measurement function by positioning the rotary switch to one 

of the icons around its perimeter. For each function, the Meter presents a standard 
display for that function (range, measurement units, and modifiers). Button choices 

made in one function do not carry over into another function. 

    All functions except current use the VOHMS and COM input terminals. The two 
current input terminals

Input for 0 A to 10.00 A current 
(20VA overload for 30 seconds 
on, 10 minutes off),
Input for 0 A to 500 mA current 
measurements.
Return terminal for all 
measurements.
Input for voltage, continuity, 
resistance, diode test, 
conductance, capacitance.

 

CAP Temp

Bluetooth

5

20A for 

30 sec

MAX 

every

15 min

TE M P

C A P

mV

Temp
A
mA

uA

AC voltage measurements
DC and AC+DC voltage 
measurements.
DC(AC) milli-volts measurements.
Resistance, Diode test, 
capacitance and CONTINUITY 
measurements. 
Frequency measurements.
Temperature measurements .
AC, dc amps measurements.
AC, dc milliamps measurements.
% 4-20MA measurements.
AC, dc microampere 
measurements up to 5,000 uA.

Ω

    

    CAP

 

4 ~ 2 0

%

TE M P

°C °F

5. Measure Function

5-1. AC Voltage Measurements

    

WARNING:

 Risk of Electrocution. The probe tips may not be long enough to 

contact the live parts inside some 240V outlets for appliances 
because the contacts are recessed deep in the outlets. As a 
result, the reading may show 0 volts when the outlet actually has 
voltage on it. Make sure the probe tips are touching the metal 
contacts inside the outlet before assuming that no voltage is 
present.

    

CAUTION:

 Do not measure AC voltages if a motor on the circuit is being 

switched 

ON or OFF

.

 Large voltage surges may occur that can 

damage the meter.

1.Set the function switch to the green 

VAC

 position.

2.Insert the black test lead banana plug into the 

negative 

COM

 jack. Insert red test lead banana 

plug into the positive

 V

 jack.

3.Read the voltage in the main display

    

 

    

 

    

 

    

 

    

 

    

 

    

 

    

 

Bluetooth

5

20A for 

30 sec

MAX 

every

15 min

TE M P

C A P

F1

HOLD

REL

RANGE

4 ~ 2 0

%

TE M P

°C °F

RANGE    SETUP   SAVE   HOLD

   

  

  

Auto range

00:00

 

      

True RMS Multimeter

 

 

12 0

0. 0

V~

0

1

2

3

4

5 V

~

F2

F3

F4

Summary of Contents for RS-989

















Reviews: