background image

 

Real Time Automation, Inc. 

20 

1-800-249-1612 

 

 

 

 

 

d)

 

Ethernet Port 1 & 2 used 

2)

 

Two Ethernet-based protocols on different IP Networks 
a)

 

Ethernet Port 1 used AND 

b)

 

Ethernet Port 2 used AND 

c)

 

Wi-Fi used 

Switch Mode

 

 Only Ethernet Port 1 is used for protocol communication 

1)

 

One Ethernet-based protocol on the IP Network (layer-2 switch) 
a)

 

Ethernet Port 1 used for direct protocol communication 

b)

 

Ethernet Port 2 available for daisy chaining devices together 
i)

 

A Ring topology is NOT supported 

2)

 

Two Ethernet-based protocols on same IP Network 
a)

 

Ethernet Port 1 used for direct protocol communication with another switch, hub, or router 

b)

 

Ethernet Port 2 available for a daisy chaining devices together 
i)

 

A Ring topology is NOT supported 

3)

 

Two Ethernet-based protocols on different IP Networks 
a)

 

Not Possible 

 must use Independent Mode 

Wireless Mode

 

 Only Wi-Fi is used for protocol communication 

1)

 

Two Ethernet-based protocols on the same IP Network into a Router 

 

 

 

 

It is recommended to leave the DNS Gateway set to 0.0.0.0 and the Ethernet Link as 
Auto-Negotiate. If configuring the gateway to use E-mail, the DNS Gateway must be 
set. 

Summary of Contents for 460PSBM-N2EW


















































































Reviews: