background image

 

RTD Embedded Technologies, Inc. 

www.rtd.com

 

 

38

 

ERES35105 

User’s Manual

 

10

 

Limited Warranty

 

 

RTD Embedded Technologies, Inc. warrants the hardware and software products it manufactures and produces to be free from defects in 
materials and workmanship for one year following the date of shipment from RTD Embedded Technologies, Inc. This warranty is limited to the 
original purchaser of product and is not transferable. 

During the one year warranty period, RTD Embedded Technologies will repair or replace, at its option, any defective products or parts at no 
additional charge, provided that the product is returned, shipping prepaid, to RTD Embedded Technologies. All replaced parts and products 
become the property of RTD Embedded Technologies. Before returning any product for repair, customers are required to contact the factory for 
a Return Material Authorization (RMA) number. 

This limited warranty does not extend to any products which have been damaged as a result of accident, misuse, abuse (such as: use of 
incorrect input voltages, improper or insufficient ventilation, failure to follow the operating instructions that are provided by RTD Embedded 

Technologies, “acts of God” or other contingencies beyond the control of RTD Embedded Technologies), or as a result of service or 

modification by anyone other than RTD Embedded Technologies. Except as expressly set forth above, no other warranties are expressed or 
implied, including, but not limited to, any implied warranties of merchantability and fitness for a particular purpose, and RTD Embedded 
Technologies expressly disclaims all warranties not stated herein. All implied warranties, including implied warranties for merchantability and 
fitness for a particular purpose, are limited to the duration of this warranty. In the event the product is not free from defects as warranted above, 
the purchaser's sole remedy shall be repair or replacement as provided above. Under no circumstances will RTD Embedded Technologies be 
liable to the purchaser or any user for any damages, including any incidental or consequential damages, expenses, lost profits, lost savings, or 
other damages arising out of the use or inability to use the product. 

Some states do not allow the exclusion or limitation of incidental or consequential damages for consumer products, and some states do not 
allow limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. 

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 

 

Summary of Contents for ERES35105HR








































Reviews: