background image

 

 

 

- page 12 of  13 

– 

Inst ruct ion and operat ing manual CVS  
SKL1200 direct  driven                                                                                                                 

(for-030/031013)

    

 

 

5.4 

HALFYEARLY INSPECTION  

 

 

* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *  

 

ONLY CARRY OUT WHEN INSTALLATION IS COOL AND AT A STANDSTILL 

 

* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *

 

 

This  check  may  only  be  carried  out  by  skilled  mechanics.  Observe  the  safety  very 
carefully, the enclosure must be removed and rotating parts will be accessible.  

 
A: 

Change the lubricating oil simultaneously w ith the truck’s engine oil, at  least tw ice 

a year.  
 

•   Open  the  oil  drain  screw   (5)  at  the  low est  point, 
drain oil.  

•   Dismantle  oil  filter  w ith  the  aid  of  a  strap  w rench. 
Lightly  oil  the  new   oil  filter  on  the  rubber  seal  and 
tighten by hand.  

•   Close  oil  drain  screw s,  fill  in  oil  as  described  in  and 
check filling level.  
 
 
 
 
(oil type 15W40 or 10W40 synthetic oil) 
 
 

 
B: 

Change the oil filter. 

 

Please find the instructions to demount the oil filter in the manual provided w ith the 
installation. 

 

 

C: 

Demount  the  non-return  valve  installed  in  the  discharge  silencer  and  check  for 
proper functioning. 

 
D: 

Check the functioning of the fan. 

 

E  

Check if the control light is on. You w ill find the safety fuse in the sw itch box. 

 
F: 

Check the shear pin coupling for leew ay space.   

 
NOTE:  
 

The operating instructions provided by the compressor manufacturer should be read 
carefully.

 

 
 
5.5 

Maintenance/inspection list  

 

Along w ith every maintenance inspection the maintenance checklist on the next page must 
be filled out. We recommend sending the checklist to RTI after filling it out. 
 
Mail: info@rti.nl 
Fax: (0031) 544-376499 
 
Hold  on  to  the  checklist,  the  checklist  can  be  handed  to  the  mechanic  w hen  the  next 
maintenance service is due or w hen the installation needs to be repaired. (Do not forget to 
take the checklist back w ith you)  

Summary of Contents for SKL1200














Reviews: