background image

Copyright © 2016 Ruckus Wireless, Inc.
Published June 2016, Part Number 800-71242-001 Rev A

Page 4 of 4

ground point (Figure 12).

CAUTION: 

The T610s AP includes one 12mm stainless steel 

M6x1 earth ground screw with split lock and flat washers. Make 
sure that any replacement screw is no longer than 12mm. If a 
screw is longer than 12mm, it can damage the AP chassis.

 

Figure 12:

Connect good earth ground to AP here

S

TEP

 9: I

NSTALLING

 

THE

 S

ECURITY

 C

ABLE

NOTE:

 

The security cable is an optional accessory that must be 

purchased separately. 

1

Thread the security cable through the mounting bracket (A) and 
through the eye on the cable itself (B), as shown in Figure 13.

2

Attach the safety cable to the AP (C) in Figure 13.

Figure 13:

Attaching the security cable

Congratulations! You have mounted your T610s access point.

I

NSTALLING

 

A

 USB D

ONGLE

To install a USB dongle, which could be an IoT radio like BLE, 
802.15.4, Z-wave or the like, remove the two 3mm hex screws, 
remove the cap, and insert the dongle into the USB port. Once 
installed, replace the cap and the hex screws, and torque the screws 
to 7 in-lbs. 

Figure 14:

Installing a USB dongle

T

ROUBLESHOOTING

CAUTION:

 

If required, you can reset the AP to its factory default 

settings by pressing the reset button located inside the PoE IN 
port. DO NOT DO THIS UNLESS SO INSTRUCTED. (Doing this 
resets the AP IP address to 192.168.0.1.)

NOTE:

 

After a reset, you can access the internal AP web interface 

using 

https://192.168.0.1

. Your device must use any 

other address from 192.168.0.2 through 192.168.0.254, with 
subnet mask 255.255.255.0. The username is 

super

, and the 

password is 

sp-admin

. Refer to the ZoneFlex Outdoor Access 

Point User Guide for information on configuring and operating the 
AP. This document is available at 

https://

support.ruckuswireless.com

.

NOTE: 

After an AP is removed from its mounting, it may drip 

some water from the channel surrounding the radome. As long as 
the AP has been operating normally, this incidental water 
collection and dripping is normal, and is not service-affecting.

Summary of Contents for T610s

Page 1: ...m português Brasil deste guia em https support ruckuswireless com Puede ver la versión en español América Latina de esta guía en https support ruckuswireless com BEFORE YOU BEGIN Before deploying your Ruckus Wireless T610s verify that all items listed in Package Contents are included in the package If any item is damaged or missing notify your authorized Ruckus Wireless sales representative Also m...

Page 2: ...le gland base 7 Hand tighten the sealing nut STEP 2 ATTACHING THE U JOINT BRACKET TO THE MOUNTING BRACKET NOTE The following mounting instructions require purchase of optional accessories that are not included in the standard T610s package The outdoor AP Mounting Bracket and safety cable are optional accessories that must be purchased separately 1 Position the U joint bracket on the mounting brack...

Page 3: ...set The linkage bracket is symmetrical and either end can be attached to the AP bracket NOTE Make sure that linkage bracket is installed with its serrated external tooth lock washer on the inside of the AP bracket flanges This ensures that the elevation adjustment does not change 1 As described in Step 4 Mounting the Linkage Bracket to the U Joint Bracket loosely assemble the AP bracket shown in F...

Page 4: ...like remove the two 3mm hex screws remove the cap and insert the dongle into the USB port Once installed replace the cap and the hex screws and torque the screws to 7 in lbs Figure 14 Installing a USB dongle TROUBLESHOOTING CAUTION If required you can reset the AP to its factory default settings by pressing the reset button located inside the PoE IN port DO NOT DO THIS UNLESS SO INSTRUCTED Doing t...

Reviews: