background image

Positioning

This appliance is to be installed in a counter top.

Avoid damaging the product during installation.

The appliance can only be used safely if it is correctly installed according to the 
safety instructions. The installer is responsible for ensuring that the appliance 
works correct when installed. 

Gas appliances must be disconnected and installed by a Gas Safe registered 
engineer. This scheme has replaced the Corgi registration scheme. For details 
visit www.gassaferegister.co.uk or call 0800 408 5500. Failure to do so will 
invalidate your guarantee, liability claims and could lead to criminal 
prosecution.

The edges of the hob must be a minimum of 60mm from a side or rear wall.

The highest point of the hob (including the burners) must be a minimum of 
700mm from the underside of any surface 

directly

above it.

The highest point of the hob (including the burners) must be a minimum of 
400mm from the underside of any surface 

either side

of the hob. If any surface 

either side

of the hob is lower than 400mm, then it must be at least 50mm 

from the outer edges of the hob.

There must be a minimum of 50mm of clearance around the hob and any 
combustible materials.

For Customer Services & Spare Parts please call

0345 208 8750

or visit us at 

https://mda.russellhobbs.com

7

600mm

420mm

420mm

700mm

100mm

Summary of Contents for RH60GH401





























Reviews: