background image

 

3

 

IMPORTANT SAFEGUARDS 

When using any electrical heater, basic safety precautions should always be followed 

including the following: 

1.  Please read the instructions carefully before using any heater. 

2.  Always ensure that the voltage on the rating label corresponds to the mains 

voltage in your home. 

3.  Incorrect operation and improper use can damage the heater and cause injury to 

the user. 

4.  The heater is intended for household use only. Commercial use invalidates the 

warranty and the supplier can not be held responsible for injury or damage 

caused when using the heater for any other purpose than that intended. 

5.  Close supervision is required when any heater is used near or by children or 

invalids. 

6.  Check the power cord and plug regularly for any damage. If the cord or the plug 

is damaged, it must be replaced by the manufacturer or a qualified person in 

order to avoid an electrical hazard. 

7.  Do not use the heater if it has been dropped or damaged in any way. In case of 

damage, take the unit in for examination and/or repair by an authorised service 

agent 

8.  To reduce the risk of electric shock, do not immerse or expose the motor 

assembly, plug or the power cord to water or any other liquid. 

9.  Never immerse the unit in water or any other liquid for cleaning purposes. 

10. Remove the plug from the socket by firmly pulling the plug. Do not pull on the 

cord to disconnect the heater from the mains. Always unplug the unit when not in 

use. 

11. The use of accessory attachments that are not recommended or supplied by the 

manufacturer may result in injuries, fire or electric shock. 

12. A short cord is provided to reduce the hazards resulting from becoming 

entangled in or tripping over a longer cord.  

13. Ensure that the cord is not in a position where it can be pulled on inadvertently. 

14. Do not allow the cord to touch hot surfaces. 

15. Use of an extension cord with this heater is not recommended. However, if it is 

necessary to use an extension lead, ensure that the lead is suited to the power 

consumption of the heater to avoid overheating of the extension cord, heater or 

Summary of Contents for RHC1960










Reviews: