RUSTICA Heavy-Duty Bypass Track System Installation Instructions Manual Download

Page: 3 / 12

R H

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

I N S T A L L A T I O N I N S T R U C T I O N S

Pencil

Tape Measure

Drill with 1/8”, 1/4”

and 3/8” bits, and

Phillips bit

Short Level

9/16” and 5/8” open

end and ratcheting

wrench

Ratchet with 9/16” and

5/8” sockets

Bypass Bracket

Track

Lag Bolts

1” Washers

Door Guide

Tools Needed

Parts Included

Track Stops

Lag Screws

Track Splice Plate Bracket

(included when two or

more tracks are needed)

Wall Mount Door Guide

(optional)

Parts and Tools

Page 3

Open Hex Nuts

PLEASE NOTE: These

instructions are specific

to a particular Track

System. Adjustments

may be needed on your

part for changes in

specifications and mea-

surements, as well as

Track Systems that are

different than these.

Summary of Contents for Heavy-Duty Bypass Track System













Search results

Summary of Contents for Heavy-Duty Bypass Track System

Reviews:

Related manuals for Heavy-Duty Bypass Track System

Brands by name

Popular brands

RUSTICA Heavy-Duty Bypass Track System, Installation Instructions Manual

Search results

Summary of Contents for Heavy-Duty Bypass Track System

Reviews:

Related manuals for Heavy-Duty Bypass Track System

Brands by name

Popular brands