3inONE-30
The
LED strip is only suitable for installation in dry
indoor rooms.
Risk of electric shock!
Be sure to have a professional electrician complete
in stallation. There is no warranty coverage for any lights
installed without observing european safety directives.
Caution!
Only connect the
LED strip to a suitable
power supply (24 V DC).
Only operate when completely unrolled.
Connect
LED strips in parallel.
Delivery includes
1 x 5 metre
LED strip
5 x in-feed connectors profi
1 x direct connector profi
Technical data
Power supply 24 V power supply with constant
output voltage
Power 36 W
Current strength 1,5 A
Radiation angle 120°
Quantity LED 150
Length maximum 5 metres per connection
Abmessungen 5000 x 10 x 2,2 mm
Bending diameter 30 mm
Compliant with the applicable
european CE directives
Safety class 3 - low voltage protection
Suitable for indoor use only
Do not cover lamps with heat-
i
Ensure that minimum
c
Use HO3VVH2-F 2x 0.75 mm cable only
f
Use low-pressure halogen
l
The lamp is suitable for moun-
t
T
L
Protection class 3 – Low-voltage 12 V.
U
Use low-voltage traction relief (except
f
H
This is only possible with specially
m
Protection class 2 – high vol-
t
Switch off voltage prior to installation.
E
Do not touch the halogen lamp with
y
Do not cover lamps with heat-
i
Ensure that minimum
c
Use HO3VVH2-F 2x 0.75 mm cable only
f
Use low-pressure halogen
l
The lamp is suitable for moun-
t
T
L
Protection class 3 – Low-voltage 12 V.
U
Use low-voltage traction relief (except
f
H
This is only possible with specially
m
Protection class 2 – high vol-
t
Switch off voltage prior to installation.
E
Do not touch the halogen lamp with
y
G
G
Figure 2
example figure
Carl-Zeiss-Str. 15
28857 Syke
With in-feed connector:
To connect a
LED strip to a power supply, use
a in-feed connector.
1.
Do not
remove the protection film at the connection position.
2. Open the shutter of the direct / in-feed connector (Fig. 2+3).
3
.
Connect the in-feed connector to the end of the
LED strip (observe polarity) and close the fastener
(Fig. 2+3).
Caution!
With soldered connections note that the soldering
tem perature is 260° C and the soldering duration a
maximum of 10 seconds per soldering point.
Only use neutral cross-linked silicon (never use silicon which
includes vinegar!).
Disposal
Dispose of electrical and electronic equipment in an
environmentally friendly manner. Please contact your local
council for further information.
Do not cover lamps with heat-
i
Ensure that minimum
c
Use HO3VVH2-F 2x 0.75 mm cable only
f
Use low-pressure halogen
l
The lamp is suitable for moun-
t
T
L
Protection class 3 – Low-voltage 12 V.
U
Use low-voltage traction relief (except
f
H
This is only possible with specially
m
Protection class 2 – high vol-
t
Switch off voltage prior to installation.
E
Installation
Risk of electric shock!
Switch off voltage prior to installation. Ensure that voltage
cannot be accidentally switched on again.
First connect the
LED strip to an controller and
then to the power supply (not included in the scope of delivery).
Caution!
On conducting surfaces, place an insulation layer between the
LED strip and surface. Surfaces must be flat, free
of dust, grease and dry.
1. Prepare surface.
2. Shorten
LED strip if necessary (Fig. 1).
3. Peel off adhesive film and gently press on
LED strip, do not press directly on the LEDs.
4. Connect
LED strip to power supply.
Shortening the LED strip
Risk of electric shock!
Always disconnect the mains plug before shortening.
LED strip can be separated in each case after
five LEDs (166,5 mm)
(Fig. 1).
Separate the
LED strip at the marked position.
For a tightly assembled LED strip is a micro side cutter or an
optional cutter required.
Connecting LED strip
With direct connector:
To connect two
LED strip together, use a direct
connector.
Do not cover lamps with heat-
i
Ensure that minimum
c
Use HO3VVH2-F 2x 0.75 mm cable only
f
Use low-pressure halogen
l
The lamp is suitable for moun-
t
T
L
Protection class 3 – Low-voltage 12 V.
U
Use low-voltage traction relief (except
f
H
This is only possible with specially
m
Protection class 2 – high vol-
t
Switch off voltage prior to installation.
E
Do not touch the halogen lamp with
y
Do not cover lamps with heat-
i
Ensure that minimum
c
Use HO3VVH2-F 2x 0.75 mm cable only
f
Use low-pressure halogen
l
The lamp is suitable for moun-
t
T
L
Protection class 3 – Low-voltage 12 V.
U
Use low-voltage traction relief (except
f
H
This is only possible with specially
m
Protection class 2 – high vol-
t
Switch off voltage prior to installation.
E
Do not touch the halogen lamp with
y
Do not cover lamps with heat-
i
Ensure that minimum
c
Use HO3VVH2-F 2x 0.75 mm cable only
f
Use low-pressure halogen
l
The lamp is suitable for moun-
t
T
L
Protection class 3 – Low-voltage 12 V.
U
Use low-voltage traction relief (except
f
H
This is only possible with specially
m
Protection class 2 – high vol-
t
Switch off voltage prior to installation.
E
Figure 3
example figure
Figure 1
example figure