background image

8

 WARNING

Disconnect the tool from the air supply and empty the 
magazine before clearing a jammed fastener. Failure to 
do so could result in serious personal injury.

If a fastener becomes jammed in the tool, disconnect the 
air hose and keep the tool pointed away from you while 
clearing the jam.
1.  Remove fasteners from the tool.
2.  Pull up on the latch and open the jam release.
3. 

,QVHUW D ÀDW EODGH VFUHZGULYHU LQWR WKH GULYLQJ

mechanism and push the driver mechanism back, 
freeing the jammed fastener.

4.  Remove the jammed fastener.
5.  Close the jam release and latch.
6.  Reconnect the tool to the air supply.
7. Reinstall fasteners.

MAINTENANCE

 WARNING

When servicing use only identical replacement parts. 
Use of any other parts may create a hazard or cause 
product damage.

 WARNING

Always wear eye protection with side shields marked to 
comply with one of the following standards:

 

Ɣ

Australian Standard – AS/NZS 1337

 

Ɣ

European Standard – CE EN166

 

Ɣ

American Standard – ANSI Z87.1

Failure to do so could result in objects being thrown into 
your eyes resulting in possible serious injury.

 WARNING

Disconnect the tool from the air supply and empty the 
magazine before performing maintenance. Failure to do 
so could result in serious personal injury.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most 
plastics are susceptible to damage from various types of 
commercial solvents and may be damaged by their use. 
Use clean cloths to remove dirt, dust, oil, grease, etc.

 WARNING

'RQRWDWDQ\WLPHOHWEUDNHÀXLGVJDVROLQHSHWUROHXP

based products, penetrating oils, etc., come in contact 
with plastic parts. Chemicals can damage, weaken or 
destroy plastic which may result in serious personal 
injury.

COLD WEATHER OPERATION

For cold weather operation, near and below freezing, 
the moisture in the air line may freeze and prevent tool 
operation. We recommend the use of air tool lubricant or 

SHUPDQHQWDQWLIUHH]HHWK\OHQHJO\FRODVDFROGZHDWKHU

lubricant.

 WARNING

Do not store tools in a cold weather environment to 
prevent frost or ice formation on the tools’ operating 
valves and mechanisms that could cause tool failure.

NOTE:

 Some commercial air line drying liquids are harmful 

to “O” rings and seals. Do not use these low temperature 
air dryers without checking compatibility.

AIR SUPPLY PRESSURE AND VOLUME

Air volume is as important as air pressure. The air volume 
supplied to the tool may be inadequate because of 

XQGHUVL]H¿WWLQJVDQGKRVHVRUIURPWKHHIIHFWVRIGLUWDQG
ZDWHULQWKHV\VWHP5HVWULFWHGDLUÀRZZLOOSUHYHQWWKHWRRO

from receiving an adequate volume of air, even though 
the pressure reading is high. The results will be a slow 
operation or reduced driving power. Before evaluating tool 
problems for these symptoms, trace the air supply from 
the tool to the supply source for restrictive connectors, 
low points containing water and anything else that would 

SUHYHQWIXOOYROXPHÀRZRIDLUWRWKHWRRO

REQUIRED DAILY CHECKLIST

1.  Disconnect the air supply from the tool and remove 

all fasteners.

2.  Check all screws, nuts, bolts, and pins on the tool. If 

any of these are loose, they must be tightened with the 
appropriate size wrench.

3.  Press the safety yoke against a workpiece to ensure 

that it moves smoothly.

4.  With the safety yoke depressed, pull the trigger. The 

trigger should move smoothly, without binding.

5.  While the tool is not loaded, connect the appropriate 

DLUVXSSO\DWEDUSVLWRWKHWRRO

 

Ɣ

Without pulling the trigger, press the safety yoke 
against a workpiece several times. The tool must 
not operate.

 

Ɣ

With the safety yoke not engaged on the workpiece, 
point the tool down and away from you and other 
persons, and pull the trigger several times. Hold 
the trigger in this position for a minimum of 5 

Summary of Contents for 6210565

















Reviews: