Ryobi CLD-120, Owner'S Operating Manual

4

INSTRUCTIONS FOR SAFE HANDLING

TRIGGER (Fig. 3)

FORWARD/ REVERSE SWITCH (Fig. 3)

1. Make sure that the tool is only connected to the voltage marked 

    on the name plate.
2. Never use the tool if its cover or any bolts are missing. If the

    cover or bolts have been removed, replace them prior to use. 

    Maintain all parts in good working order.
3. Always secure the tool when working in elevated positions.
4. Never touch the blade, drill bit, grinding wheel or other moving 

    parts during use.
5. Never start the tool when its rotating component is in contact 

    with the work piece.
6. Never lay the tool down before its moving parts have come to a 

    complete stop.

7. ACCESSORIES :

    The use of accessories or attachments other than those

    recommended in this manual might present a hazard.

8. REPLACEMENT PARTS :

    When servicing use only identical replacement parts.

CORDLESS DRIVER DRILL SAFETY PRECAUTIONS

DISPOSAL OF THE EXHAUSTED BATTERY

SPECIFICATIONS

1. Be aware that since this tool does not have to be plugged into 

    an electrical outlet, it is always in operating condition.
2. First, charge the battery.
3. Be sure the battery holder is securely snapped in place.
4. When not in use, lock the trigger.
5. When operating at high places, be aware of things below you.
6. Before drilling into walls, ceilings or floors, ensure that there are

    no concealed power cables inside.

Battery

Chuck capacity 

No load speed 

Max torque

Drilling capacity

Clutch position

Charging time 

Net weight 

12V, 1,300mAh Li-ion

10mm

0-700min

-1

12Nm

steel: 8mm

wood: 19mm

 21 + 1

3-5hours

1kg

14.4V, 1,300mAh Li-ion

10mm

0-700min

-1

12Nm

steel: 8mm

wood: 19mm

 21 + 1

3-5hours

1.1kg

DESCRIPTION

Li-ion batteries must be recycled.

Take the battery to the shop from which it was purchased as soon

as the post-charging battery life becomes too short for practical use.

Do not discard the exhausted battery.

APPLICATIONS

KEYLESS CHUCK AND MOUNTING THE BIT (Fig. 1)

(Use only for the purposes listed below.)
1. Drilling wood, ceramics, plastics, fiberglass, metal and concrete.

2. Driving and removing machine screws, wood screws, tapping 

    screws etc.

This tool comes equipped with a keyless chuck to easily mount

the bit.

Insert the bit into the chuck as far as it will go and rotate the chuck

clockwise to securely tighten the bit.

The bit can be removed by turning the chuck counterclockwise.

WARNING!

 Make sure to insert the drill bit straight into the chuck

jaws. Do not insert the drill bit into the chuck jaws at an angle then

tighten (Fig. 2). This could cause the drill bit to be thrown from the 

drill, resulting in possible serious personal injury or damage to the 

chuck.

This tool is started and stopped by depressing and releasing the

trigger (6).

The drill speed is variable from 0 through 400 (Low speed position) 

or from 0 through 1,500 (High speed position) by controlling the 

trigger-squeezing force.

To change the direction of rotation, stop the tool by releasing the

trigger and push the forward/ reverse switch (4) to the opposite

side. When the reversing switch is set to the right position, the

direction of rotation will be clockwise when viewed from the handle 

end of the drill. When the reversing switch is set to the left position, 

the direction of rotation will be counter-clockwise.
The trigger can be locked by positioning the reversing switch at 

the center. Lock the trigger whenever the tool is not in use.

LED WORK LIGHT (Fig. 3)

This tool is equipped with a LED work light (5) to illuminate the tip 

of a bit. The light turns on by depressing the trigger.

FASTENING TORQUE ADJUSTMENT (Fig. 4)

CHARGING BATTERY PACK (Fig. 5, 6)

This tool is equipped with a clutch which enables the fastening

torque to be adjusted in 21 stages.

To use the tool in the screwdriver mode, set one of the numbers “1” 

to “21” indicated on the torque adjustment cap (2) to the marked 

(      ) on the top side of housing. The higher number on the torque 

adjustment cap, the greater the torque.

To use the tool in the drill mode, set the drill mark (      ) on the

torque adjustment cap to the point. The clutch does not operate

when the tool is used in the drill mode.

The battery pack for the tool has been shipped in a low charge

condition to prevent possible problems. Therefore, you should

charge it prior to use.

NOTE:

Batteries will not reach full charge the first time they are

charged. Allow several cycles for them to fully charge.

• Charge battery pack only with the charger provided.
• D

o not place charger in an area of extreme heat or cold. It will  

  work best at temperatures above 10°C and below 38°C.

• M

ake sure power supply is normal house voltage, 230 volts,  

  50Hz, AC only.

CAUTION!

CLD-120

CLD-144

1. Keyless chuck

2. Torque adjustment cap

3. Forward/ Reverse switch

4. LED work light

5. Trigger

6. Battery clip

7. Battery pack

8. Charging adaptor

9. Charging jack