Ryobi R18GS18, Manual

RYOBI

®

 WARRANTY APPLICATION CONDITIONS

In addition to any statutory rights resulting from the purchase, this product is 

covered by a warranty as stated below.
1.  The warranty period is 24 months for consumers and commences on the 

date the product was purchased. This date has to be documented by an 

invoice or other proof of purchase. The product is designed and dedicated to 

consumer and private use only. So there is no warranty provided in case of 

professional or commercial use. This warranty applies only on new products.

2.  There is a possibility to extend for a part of the range of power tools (AC/

DC) the warranty period over the period described above using the 

registration on the www.ryobitools.eu website. The eligibility of products 

for extended warranty is clearly displayed in stores and / or on packaging 

and is contained within the product documentation. The end user is 

required to register his/her newly-acquired products online within 30 days 

from  the  date  of  purchase.  The  end  user  may  register  for  the  extended 

warranty in his/her country of residence if listed on the online registration 

form where this option is valid. Furthermore, end users must give their 

consent to the storage of their personal data that is required to be entered 

online. They must also accept the terms and conditions. The registration 

confirmation receipt, which is sent out by e-mail, and the original invoice 

showing the date of purchase will serve as proof of the extended warranty.

3.  The warranty covers all defects of the product during the warranty 

period due to faults in workmanship or material at the purchase date. 

The  warranty  is  limited  to  repair  and/or  replacement  and  does  not 

include any other obligations including but not limited to incidental or 

consequential damages. The warranty is not valid if the product has 

been misused, used contrary to the instruction manual, or has been 

incorrectly connected to a power supply. This warranty does not apply to:

– any damage to the product that is the result of improper or lack of maintenance

– any product that has been altered or modified

– any product where original identification (trade mark, serial number) markings 

have been defaced, altered or removed

– any damage caused by non-observance of the instruction manual

– any product not displaying the CE approval mark on the rating plate

– any product that has been attempted to be repaired by a non-authorised 

warranty service centre or without prior authorisation by Techtronic Industries

– any product connected to improper power supply (amps, voltage, frequency)

– any damage caused by external influences (water, chemical, physical, shocks) 

or foreign substances

– normal wear and tear spare parts

– inappropriate use, overloading of the tool

– use of non-approved accessories or parts

– Power tool accessories provided with the tool or purchased separately, 

including but not limited to screw driver bits, drill bits, abrasive discs, sand 

paper and blades, lateral guide, etc.

– Components (parts and accessories) subject to natural wear and tear, including 

but not limited to service & maintenance kits, carbon brushes, bearings, chuck, 

SDS drill bit attachment or reception, power cord, auxiliary handle, transport 

carry case, sanding plate, dust bag, dust exhaust tube, felt washers, impact 

wrench pins & springs, etc.

4.  For servicing, the product must be sent or presented to a RYOBI 

authorised service station listed for each country in the following list of 

service station addresses. In some countries your local RYOBI dealer 

undertakes to send the product to the RYOBI service organisation. When 

sending a product to a RYOBI service station, the product should be 

safely packed without any dangerous contents such as petrol, marked 

with sender’s address and accompanied by a short description of the fault.

5.  A  repair  /  replacement  under  this  warranty  is  free  of  charge.  It  does  not 

constitute an extension or a new start of the warranty period. Exchanged 

parts or products become our property. In some countries delivery 

charges or postage will have to be paid by the sender. Your statutory 

rights arising from the purchase of the product remain unaffected

6.  This warranty is valid in the European Community, Switzerland, Iceland, 

Norway, Liechtenstein, Turkey, Russia and the United Kingdom. Outside 

these areas, please contact your authorised RYOBI dealer to determine if 

another warranty applies.

EC DECLARATION OF CONFORMITY

Manufacturer: Techtronic Industries GmbH

Max-Eyth-Straße 10, 71364 Winnenden, Germany

We declare as the manufacturer under our sole responsibility that the product 

mentioned below

Stapler

Brand: RYOBI

Model number: R18GS18

Serial number range: 

47565901000001 - 47565901999999

fulfills all the relevant provisions of the following European Directives, European 

Regulations and harmonised standards.

2006/42/EC, 2014/30/EU, 2011/65/EU

EN 55014-1:2017+A11:2020, EN 55014-2:2015,  

EN 60745-1: 2009+A11:2010, EN 60745-2-16:2010 

EN IEC 63000:2018

Todd Chipner

Vice President, Quality – Ryobi Asia

Winnenden, 

Mmm. dd

, 2021

Authorised to compile the technical file:

Alexander Krug, Managing Director

Techtronic Industries GmbH

Max-Eyth-Straße 10, 71364 Winnenden, Germany

RYOBI is a trade mark of Ryobi Limited, 

and is used under license.

© 2021 Techtronic Cordless GP.

AUTHORISED SERVICE CENTRES

Any request or issue with the product can be addressed to your local authorised 

service centres (visit www.ryobitools.eu) or directly to: Techtronic Industries GmbH, 

Max Eyth Straße 10, 71364 Winnenden, Germany. Please state the serial number 

and product type printed on the label.

GB-DECLARATION OF CONFORMITY

Manufacturer: Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany

We declare as the manufacturer under our sole responsibility that the product 

mentioned below 

Stapler

Brand: RYOBI

Model number: R18GS18

Serial number range: 

47565901000001 - 47565901999999

fulfills all the relevant provisions of the following Regulations: S.I. 2008/1597 (as 

amended), S.I. 2016/1091 (as amended), S.I. 2012/3032 (as amended) and that 

the following designated standards have been used:

BS EN 55014-1:2017+A11:2020, BS EN 55014-2:2015,  

BS EN 60745-1: 2009+A11:2010, BS EN 60745-2-16:2010 

BS EN IEC 63000:2018

Todd Chipner

Vice President, Quality - Ryobi Asia

Winnenden, 

Mmm. dd

, 2021

Authorised to compile the technical file:

Alexander Krug, Managing Director

Techtronic Industries GmbH

Max-Eyth-Straße 10, 71364 Winnenden, Germany

For technical review, sent 03 Jun 2021