Ryobi R18ST50 Original Instructions Manual Download

Page: 4 / 120

| English

■

Do not point the product towards yourself or anyone
nearby when adjusting the depth of drive.

ADDITIONAL BATTERY SAFETY WARNINGS

WARNING

To reduce the risk of

re, personal injury, and product

damage due to a short circuit, never immerse your
tool, battery pack or charger in

uid or allow a

uid to

ow inside them. Corrosive or conductive

uids, such

as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.

RESIDUAL RISKS

even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise and the operator
should pay special attention to avoid the following:

■

Damage to hearing

Note:

Always wear effective hearing protection and limit

exposure to noise.

■

Injury to the eyes caused by incorrectly driven fasteners

or flying dust and debris.

Note:

Always wear suitable eye protection.

■

Injury caused by vibration

Note:

Hold the product by designated handles and limit

exposure to vibration. See Risk Reduction.

■

Lacerations caused by contact with sharp points.

Note:

Take extra care when handling or loading

fasteners.

■

The product is heavy.
Note: The product is heavy. Beware of muscle strain
when operating the product for extended periods,
especially if using overhead.

RISK REDUCTION

It has been reported that vibrations from handheld tools
may contribute to a condition called Raynaud’s Syndrome
in certain individuals. Symptoms may include tingling,
numbness and blanching of the

ngers, usually apparent

upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking, and work practices
are all thought to contribute to the development of these
symptoms. There are measures that can be taken by the
operator to possibly reduce the effects of vibration:

■

Keep your body warm in cold weather. When operating
the product, wear gloves to keep the hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud’s Syndrome.

■

After each period of operation, exercise to increase
blood circulation.

■

Take frequent work breaks. Limit the amount of
exposure per day.

If you experience any of the symptoms of this condition,
immediately discontinue use and see your doctor about
these symptoms.

WARNING

Injuries may be caused, or aggravated, by prolonged
use of a tool. When using any tool for prolonged periods,
ensure you take regular breaks.

KNOW YOUR PRODUCT

See page 83.

1. Activation foot
2.  Wire and screen accessory
3.  Drive force indicator
4.  Depth adjustment knob
5. Magazine
6. Switch trigger
7.  Handle, insulated gripping surface
8. Belt clip
9. Magazine latch
10. Battery port
11. 14.3 mm staples
12. 6.4 mm staples

MAINTENANCE

WARNING

The product should never be connected to a power supply
when you are assembling parts, making adjustments,
cleaning, performing maintenance, or when the product
is not in use. Disconnecting the product will prevent
accidental starting that could cause serious injury.

■

When servicing, use only original manufacturer’s
replacement parts, accessories and attachments.
Use of any other parts may create a hazard or cause
product damage.

■

Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.

■

Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to various types of commercial
solvents and may be damaged by their use. Use clean
cloths to remove dirt, carbon dust, etc.

■

For greater safety and reliability, all repairs should be
performed by an authorised service centre.