Ryobi RA-NP2325-S, Operator'S Manual

6

 WARNING

The tool is capable of driving a fastener without making 
contact with a workpiece. Always point the tool away 
from yourself or others and always direct the fastener 
toward the work surface before pulling the trigger. 
Failure to do so could result in possible serious 
personal injury.

Connect the tool to the air supply with a 1/4 in. female 
quick connector. For maximum tool performance, a 3/8 in. 

VXSSO\OLQHDQG¿WWLQJVDUHUHTXLUHG

NO-MAR PAD

6HH¿JXUH

The no-mar pad attached to the nose of the product helps 
prevent marring and denting when working with softer 
woods.

 WARNING

Disconnect the product from the air supply before 
removing or replacing the no-mar pad. Failure to do so 
could result in serious personal injury.

The pad can be removed by pulling it down and away from 

WKHQRVH7RUHSODFHWKHSDG¿WLWLQWRSODFHRYHUWKHQRVH

LOADING THE TOOL WITH FASTENERS

6HH¿JXUH

 WARNING

Keep the tool pointed away from yourself and others 
when loading fasteners. Failure to do so could result in 
possible serious personal injury.

 WARNING

2QO\ WKRVH IDVWHQHUV VSHFL¿HG XQGHU 6SHFL¿FDWLRQV
PD\EHXVHG:KHQ¿OOLQJWKHPDJD]LQHKROGWKHWRRO

so that the nose is not pointing towards the operator or 
any other person or animals.

 WARNING

The tool’s driving mechanism may cycle when the tool 

LV¿UVWFRQQHFWHGWRWKHDLUVXSSO\$OZD\VFRQQHFWWKH

tool to a pressurized air supply before loading fasteners 
to prevent injury from unintended cycling. Always make 
sure the tool’s magazine is empty at the beginning of 
each work session, before connecting to an air supply.

1.  Connect the tool to the air supply.
2. Release the magazine latch and slide open the 

magazine.

3.  With the nose of the tool pointed away from you, feed 

a strip of fasteners into the magazine. Be sure the 
fasteners are pointed downward.

4.  Close the magazine.

 WARNING

Use only the fasteners recommended for use with this 
tool. The use of any other fasteners can result in tool 
malfunction, leading to serious injuries.

 WARNING

Never load fasteners with the trigger activated. Doing 
so could result in possible serious personal injury.

 WARNING

Do not use fasteners with width smaller than that stated 

LQ6SHFL¿FDWLRQV'RLQJVRPD\FDXVHIDVWHQHUVWRH[LW

the tool prematurely through the guide track. Do not use 
hardened fasteners with pneumatic tools. This could 
lead to excessive wear of the guide body and allow 
fasteners to exit the back of the guide body, leading to 
serious personal injury.

DRIVING A FASTENER

6HH¿JXUH

 WARNING

Do not pull the dual actuation trigger system unless the 
nose is pressed against the work surface. Accidental 
actuation will occur and could cause serious personal 
injury.

Avoid triggering the fastener driving tool if the magazine 
is empty.
Any defective or improperly functioning fastener driving tool 
must immediately be disconnected from the compressed 
air supply and passed to a specialist for inspection.
In the event of longer breaks in work or at the end of the 
working shift, disconnect the tool from the compressed air 
supply and it is recommended to empty the magazine.
The compressed air connectors of the fastener driving tool 
and the hoses should be protected against contamination, 
the ingress of coarse dust chips, sand, etc, will result in 
leaks and damage to the fastener driving tool and the 
couplings.

Single sequential actuation mode

The tool employs single sequential actuation mode.
1.  Connect the tool to the air supply.
2.  Load the tool with fasteners.
3. 

*ULSWKHWRRO¿UPO\WRPDLQWDLQFRQWURO3UHVVWKH

nose