background image

18

TROUBLESHOOTING

Problem

Possible Cause

Solution

Cutting tall grass at ground

level.

Operating trimmer at part

throttle.
Operating trimmer at part

throttle
Check oil/fuel mixture.
Air filter dirty.

Cut tall grass from the top down to prevent

wrapping.

Operate trimmer at full throttle.

Operate trimmer at full throttle.

Use fresh fuel and the correct 2-stroke oil mix.
Clean per instruction in Maintenance Section.

Grass wraps around

driveshaft housing and

line head

Oil drips from muffler

SERVICE

Now that you have purchased your tool, should a need ever exist of repair or service, simply contact your

nearest Ryobi Authorised Service Centre or other qualified service organistion. Be sure to provide all

pertinent facts when you call or visit.

SYMBOLS

SYMBOL

SIGNAL

MEANING

DANGER:

Indicates an imminently hazardous situation, which, if not avoided, will

result in death or serious injury.

WARNING

Indicates a potentially hazardous situation, which, if not avoided, could

result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation, which, if not avoided, may result

in minor or moderate injury.

CAUTION

(Without Safety Alert Symbol) Indicates a situation that may result in

property damage.

Recycle Symbol

Waste electrical products should not be disposed of with 

household waste. Please recycle where facilities exist. 

Check with your Local Authority or retailer for recycling 

advice.

CE Marking

Conforms to relevant safety standards.  

Summary of Contents for RBC-33





















Reviews: