background image

9

OPERATION

WARNING.

Do not allow familiarity with

this product to make you careless.

Remember that a careless fraction of a

second is sufficient to inflict serious

injury.

WARNING.

Always wear eye protection

with side shields marked to comply with

ANSI Z87.1, along with hearing

protection. Failure to do so could result

in objects being thrown into your eyes

and other possible serious injuries.

WARNING.

Never use blades, flailing

devices, wire, or rope on this product.

Do not use any attachments or

accessories not recommended by the

manufacturer of this product. The use of

attachments or accessories not

recommended can result in serious

personal injury.

WARNING.

Operation of this equipment

could create sparks that can start fires

around dry vegetation. A spark arrestor

may be replaced. The operator should

contact local fire agencies for laws or

regulations relating to fire prevention

requirements.

NOTE.

Before each use, inspect the entire product

for damaged, missing, or loose parts such as

screws, nuts, bolts, caps, etc. Tighten securely all

fasteners and caps and do not operate this product

until all missing or damaged parts are replaced.

Please contact customer service or a qualified

service center for assistance.

ETHANOL-BLENDED FUELS

NOTE:

Do not use E15 or E85 fuel in this product.

It is a violation of federal law and will damage the

unit and void your warranty. Only use unleaded

gasoline containing up to 10% ethanol.

FUELING AND REFUELING THE TRIMMER

WARNING.

Petrol and its vapors are

highly flammable and explosive. To

prevent serious personal injury and

property damage, handle it with care.

Keep away from ignition sources and open flames,

handle outdoors only, do not smoke and wipe up

spills immediately.

FUEL MIXTURE

This product is powered by a 2-stroke engine and

requires pre-mixing petrol and 2-stroke oil. Pre-mix

unleaded petrol and 2-stroke engine oil in the

container provided.
This engine is certified to operate on unleaded

petrol intended for automotive use with an octane

rating of 87 ([R + M] / 2) or higher.
Do not use any type of pre-mixed petrol / oil from

fuel service stations, this includes the pre-mixed

petrol / oil intended for use in mopeds,

motorcycles, etc.
Use synthetic 2-stroke oil only. Do not use

automotive oil or 2-stroke outboard oil.
Mix the 2-stroke oil into the petrol. This is a 25:1

ratio.
Mix the fuel thoroughly and also each time before

fueling.
Mix in small quantities. Do not mix quantities larger

than usable in a 30 day period. Synthetic 2-stroke

oil containing a fuel stabilizer is recommended.

FILLING THE FUEL TANK

Clean surface around fuel cap to prevent

contamination.
Loosen fuel cap slowly. Rest the cap on a clean

surface, Fig.10.
Carefully pour the mixed fuel into the tank. Avoid

spillage. Prior to replacing the fuel cap, clean and

inspect the gasket.
Immediately replace fuel cap and hand tighten.

Wipe up any fuel spillage. Move 9 m away from

refueling site before starting engine.
Note: It is normal for smoke to be emitted from a

new engine after first use.

Fig. 10

Summary of Contents for RBC-33





















Reviews: