background image

4

ENGLISH

Read the Operator’s Manual

To reduce the risk of injury, user must read and understand 
operator’s manual before using this product.

Keep Bystanders Away

Keep all bystanders at least 15m away.

Wear Eye Protection 

Always wear safety goggles or safety glasses with side 
shields and if necessary, a full face shield when operating 
this product.

Long Hair 

Failure to keep long hair away from the air inlet could 
result in personal injury.

Loose Clothing

Failure to keep loose clothing from being drawn into air 
intake could result in personal injury.

Sharp Blade

Danger – Keep hands and feet away from blade

No Hands Symbol

Failure to keep your away from the blade will result in 
serious personal injury.

Certificate Mark 

Conforms to relevant standards for electromagnetic 
compatibility

 

Do not expose to moisture

Do not use this tool in the rain. Avoid using it in damp 
conditions.

The following signal words are meanings are intended to explain the levels of risk associated with this product.

SYMBOL

SIGNAL

MEANING

DANGER:

Indicates an imminently hazardous situation, which, if not avoided, will result 
in death or serious injury.

WARNING:

Indicates a potentially hazardous situation, which, if not avoided, could result 
in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation, which, if not avoided, may result in 
minor or moderate injury.

CAUTION:

(Without Safety Alert Symbol) Indicates a situation that may result in property 
damage.

SERVICE

Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. 
For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for repair. When 
servicing, use only identical replacement parts.

 WARNING:

 

To avoid serious personal injury, do not attempt to use this product until you read thoroughly and understand 
completely the operator’s manual. If you do not understand the warnings and instructions in the operator’s 
manual, do not use this product. Call Ryobi customer service for assistance.

Summary of Contents for RED1520G










Reviews: