background image

SPECIFIC SAFETY rulES For lInE TrImmEr

 

1.   Your  line  trimmer  is  a  high-speed,  fast  cutting 

power tool. The electrical connection and cutting 

tools are potential sources of danger. Therefore, 

special safety precautions must be taken to re-

duce the risk of personal injury.

  2.   Never  allow  children  or  people  unfamiliar  with 

these  instructions to use the line trimmer.

  3.   The  operator or user of this  line  trimmer  is  re-

sponsible for accidents or hazards occurring to 

other people or their property.

  4.   Keep children and bystanders away. Never trim 

while people are close by.

  5.   Always wear proper footwear and long trousers.
  6.   Do not operate this line trimmer when barefoot or 

wearing open sandals.

  7.   Never use the line trimmer with a damaged guard 

or without the guard in place.

  8.   Never work with line trimmer while under the in-

fluence of alcohol or drugs.

  9.   Never attempt to modify your line trimmer in any 

way  since  it  may  increase  the  risk  of  personal 

injury. Do not use wire or metal reinforced line. 

We shall not be liable to any personal injury or 

damage to property caused by a modification of 

the tool.

  10.  Do not run with the line trimmer.
  11.   Only use your line trimmer for cutting grass and 

weeds, never for other purposes.

  12.   Only  use  the  line  trimmer  in  daylight  or  strong 

artificial light.

  13.   We recommend, using a Residual Current De-

vice  (RCD)  with  a  tripping  current  of  not  more 

than 30mA.

  14.   Use  only  extension  cables  suitable  for  outdoor 

use, preferably with a high visibility cord. Specifi

-

cation as below:

For  extension  cables  up  to  15  meters,  use  a 

wire with a cross section of 1.5mm

2

For extension cables over 15 meters and less 

than 40 meters, use a wire with a cross section 

of 2.5mm

2

  15.   Before  use,  check  the  line  trimmer  is  in  good 

condition  and  that  it  is  operating  properly.  Pay 

Special attention to extension cable, power out-

let, switch, and cutting head.

  16.   Before use, check the line and extension cords. 

Do not use the line trimmer if the cord is dam-

aged or worn.

  17.   Protect your extension cable from sharp objects, 

excessive heat, and damp or wet locations.

  18.   Keep the extension cord away from rotating ny-

lon line.

  19.   If the insulation on the power cable or extension  

cable  is  damaged  during  use,  disconnect  the 

power  supply  immediately  and  have  the  dam-

aged cable replaced. Do not touch the cable be-

fore disconnecting the supply!

  20.   Switch  on  the  line  trimmer  according  to  these 

instructions  and  keep  you  hands  and  feet  well 

away from the cutting line!

 

21.   Always hold your line trimmer firmly, make sure 

you  always maintain a good balance and secure 

footing.

  22.   Make sure the open side of the protection guard 

is  pointing away from yourself before you switch 

on the line trimmer.

  23.   Do not operate the line trimmer on wet grass, or 

under damp conditions.

  24.   Take special care in slippery conditions on slopes 

and uneven ground.

  25.   Watch for hidden obstacles such as tree stumps 

and roots to avoid stumbling.

  26.   Check the cutting head at regular intervals. If the  

behavior  changes  (excessive  noise,  vibration 

etc.) immediately:
Switch off!

Holding  the  trimmer  firmly  press  the  head  

against  the  ground  and  bring  to  a complete 

stop.
Disconnect the mains supply.

Check  the  condition  of  the  cutting  head;  look  

for  damage,  missing  parts  and cracks.

  27.   Have the damaged cutting head replaced imme-

diately even if it only has superficial cracks. Nev

-

er attempt to repair a damaged cutting head.

  28.   Only use original cutting heads and replacement 

spools. Never use metal cutting lines.

 

29.   

Warning!

Danger  of  injury  by  the  line  cutting  device. Af-

ter replacing a spool, be sure to bring the unit 

into normal working position before turning it on 

again.

  30.   Clean the plastic parts with damp cloth only. 
  31.   Never leave your grass trimmer outdoors in the 

rain. Store your tool in a dry place, keep out of 

reach of children.

4

Summary of Contents for RLT-800

















Reviews: