5
HANDLE BAR
1. Push the bolt through the holes of connection plate.
(Fig. 1)
2. Align the two holes of insulation plate onto the bolt and
pin, make sure the insulation plate and connection plate
fit closely.
(Fig. 2)
3. Align the two holes of lower handle onto the same bolt
and pin, make sure the lower handle and insulation plate
fit closely.
(Fig. 3)
4. Tighten the locking knobs (12) onto the bolt.
(Fig. 4)
5. Repeat on the other side.
6. Position the upper handle bar to the lower handle bar.
Insert the locking knobs (12) and tighten.
(Fig. 5)
NOTE!
Hand tighten only as this knob needs to be
released for storage.
7. Repeat on the other side.
NOTE!
While assembling the lower handle to baseplate, you
can choose holes either inner side or outer side, to adjust the
handle in your comfortable operation height.
(Fig. 6)
8. Position the cable cleat (10) in the upper handle.
(Fig. 7)
9. Use cable retainer (3) to keep cable in place.
ASSEMBLY
CABLE CLEAT
The power supply cable should be inserted and looped
around the Cable cleat, this will remove any strain being
placed on the Switch control unit.
ATTACHING THE GRASS CATCHER
1. Raise the rear deflector (4) on the mower deck.
2. Pass the grass catcher (7) under the handle bar, align the
attachment hooks and place the grass catcher in to
position.
(Fig. 8)
3. Lower the rear deflector , so that it now rests on the grass
catcher.
WARNING!
When mowing do not allow the motor to labour
particularly in heavy conditions. When the motor labours the
speed of the motor drops and you will hear a change in the
motor sound, when this occurs stop mowing, release the
switch lever and raise the height of cut. Failure to do so
could damage the machine.
1. Areas of heavy growth should be mown without collecting the
clippings.
2. If collection is required, firstly mow the area using the maximum
cutting height setting, without the grass collection bag attached.
3. Allow the clippings to dry out.
4. Attach the grass collection bag and mow the area, again using the
maximum cutting height setting.
NOTE!
To prevent damage to the grass, do not remove
more than one third of the grass’s height on any one cut.
NOTE!
When the blade becomes jammed or if the motor is
overloaded, remove the plug from the power supply.
Clear any obstruction and wait for a few minutes before
continuing to use the mower.
NOTE:
The blade continues to rotate for a few seconds
after the machine is switched off. Allow the motor/blade to
stop rotating before switching “on” again. Do not rapidly
switch off and on.
For the first cut of the season, a high cutting adjustment
should be selected.
OPERATION
ADJUSTING THE CUTTING HEIGHT
NOTE!
Stop, release switch lever and wait until the motor
stops before adjusting height. The blades continue to rotate
for a few seconds after the machine is switched off, a
rotating blade can cause injury.
1. Move the cutting height adjustment lever (8) sideways, to
disengage it from the locking notch.
2. Pull the lever (8) backwards to lower the cut height. Push
forwards to raise the cut height. (Fig. 9)
3. Release the lever in the required position, ensuring that it
locks firmly into one of the five notched settings.
STARTING AND STOPPING
Starting:
1. Set the mower to the required ‘cutting height’.
2. Press and hold the safety button (2).
3. Squeeze the switch lever (1) towards the handle. (Fig. 10)
4. Release the safety button.
Stopping:
Release the switch lever.
MOWING
Place the lawnmower on the edge of the lawn, as close to
the power point as possible. Work away from the power
point.
Position the cable to opposite side (already cut) at the end
of each turn.
HEAVY GROWTH
5. Progressively lower the cutting height setting and mow the area
again until the required finish is obtained.
RM-1800
230V~50Hz
Voltage
1,800W
Power input
2,850min
-1
No load speed
460mm
Cutting width
20/30/40/50/55/65mm
Cutting height
45L
Collection box capacity
22.6kg
Net weight
