background image

TROUBLESHOOTING

Problem

Possible causes

Solution

Fluctuating pressure

Pump sucking air

Check that hoses and 

connections are air tight. 

Dirty, worn-out, or stuck 

valves

Bring the product to an 

authorised service centre for 

service or repair. 

Worn-out pump seals

Bring the product to an 

authorised service centre for 

service or repair. 

Product stops

Thermal sensor activated

Leave the cleaner for 15 

minutes to cool down. 

Partially blocked nozzle

Clean the nozzle.

Product pulsating 

Air in inlet hose/pump

Allow the product to run with 

open trigger until regular 

working pressure resumes. 

Inadequate supply of mains 

water 

Check that the water 

supply corresponds to the 

specifications required (see 

model tag). Avoid using long, 

thin hoses.

Partially blocked nozzle

Clean the nozzle.

Blocked water filter

Clean the filter.

Kinked hose

Straighten out hose.

Product starts, but no water 

comes out 

Frozen pump/hoses or 

accessory

Wait for pump/hoses or 

accessory to thaw.

No water supply 

Connect the water inlet port to 

a water supply.

Blocked water filter 

Clean the filter.

Blocked nozzle

Clean the nozzle.

No detergent

Nozzle adjusted to high 

pressure

Adjust to low pressure.

Summary of Contents for RY170PWA

























Reviews: