SYMBOLS IN THIS MANUAL
Parts or accessories sold separately
Note
Warning
UNPACKING
See page 244-245.
Ŷ
Remove and set aside all accessible packaging
and wrap from the unit and parts. Do not discard the
packing material until you have carefully inspected and
satisfactorily operated the product.
Ŷ
Inspect the product carefully to ensure that no breakage
or damage occurred during shipping.
Ŷ
If any parts are damaged or missing, contact an
authorised service centre. Do not assemble the
product until the parts are replaced with new original
manufacturer’s parts. Assembling the product with
damaged, missing, or incorrect parts could result in
serious personal injury.
Ŷ
If any parts are already assembled to the product when
you unpack it, verify that the part is assembled correctly,
is properly tightened, and is torqued correctly (where
applicable) before proceeding to the next assembly step.
The use of a product that may have been improperly
assembled could result in serious personal injury.
ASSEMBLY
See page 248-250.
Ŷ
The product should be assembled while positioned on
the bottom frame. When assembly is complete, set the
cutting deck to its maximum height, then position a ramp
next to the frame bottom, and slowly and carefully drive
the product off the frame.
Ŷ
Strictly adhere to all torque wrench tightening
specifications. Failure to do so could cause serious
personal injury.
Ŷ
To prevent accidental starting that could cause serious
personal injury, always remove the start key from the
product when assembling the parts.
Ŷ
Use care when driving the product off of the frame, and
step on the brake pedal as needed to control the speed.
The product freely rolls if it is moved on an inclined
surface without stepping on the brake pedal or engaging
the parking brake. Failure to follow these instructions
can result in loss of control and result in death, serious
personal injury, or property damage.
Ŷ
If no ramp is available, slowly and carefully drive the
product off the frame in reverse while looking down and
behind. Driving the product off the frame in the forward
direction without a ramp can cause damage to the
cutting deck.
10
Original Instructions
Summary of Contents for RY48RM76A
