background image

4

 

Do not use near underground electric cables, telephone 
lines, pipes, or hoses. If in doubt, contact your utility or 
telephone company to locate underground services.

 

If the unit strikes a foreign object, stop the engine, dis-
connect the spark plug, thoroughly inspect the machine 
for any damage, and repair the damage before restarting 
and operating the machine. 

 

Never leave the operating position when the engine is 
running.

 

Stop the engine and disconnect the spark plug before 
unclogging the tines and when making any repairs, ad-
justments, or inspections.

 

Do not overload the machine capacity by cultivating too 
deep in a single pass or at too fast a rate. 

 

Stay alert. Watch what you are doing. Use common sense. 
Do not operate cultivator when you are tired.

 

Be aware that the equipment may unexpectedly bounce 
upward or jump forward if the tines should strike buried 
obstacles such as large stones, roots, or stumps. 

 

Never operate the equipment on a slope.

 

Use extreme caution when pulling the machine towards 
you.

 

Start the engine carefully according to instructions from 
a normal operating position and with feet well away from 
the tines. Do not force cultivator. It will do the job better 
and with less likelihood of a risk of injury at the rate for 
which it was designed.

 

When not in use, cultivator should be stored indoors in 
a dry, locked up place — out of the reach of children.

 

Maintain cultivator with care. Keep tines clean for best 
performance and reduce the risk of injury. Follow instruc-
tions for lubrication and changing accessories. Inspect 
cultivator cord periodically and, if damaged, have it re-
placed. Keep handles dry, clean, and free from grease 
and oil.

 

Check damaged parts. Before further use of this culti-
vator, a guard or other part that is damaged should be 
carefully checked to determine that it will operate properly 
and perform its intended function. Check for alignment 
of moving parts, binding of moving parts, breakage of 
parts,  mounting,  and  any  other  condition  that  may  af-
fect its operation. A guard or other part that is damaged 
should be properly repaired or replaced by an authorized 
service center unless otherwise indicated elsewhere in 
this manual.

REFUELING

 

Fuel is highly flammable. Take precautions when using 
to reduce the chance of serious personal injury.

 

Store fuel in a cool, well-ventilated area, safely away from 
spark and/or flame-producing equipment.

 

Store  fuel  in  containers  specifically  designed  for  this 
purpose.

 

Only refuel outdoors and do not smoke while refueling.

 

Add fuel before starting the engine. Never remove the cap 
of the fuel tank or add fuel while the engine is running or 
when the engine is hot.

 

If fuel is spilled, do not attempt to start the engine but 
move the machine away from the area of spillage and 
avoid  creating  any  source  of  ignition  until  fuel  vapors 
have dissipated.

 

Replace all fuel tank and container caps securely.

 

When draining the fuel tank, use an approved fuel storage 
container while in a well-ventilated area.

 

Save  these  instructions.  Refer  to  them  frequently  and 
use them to instruct others who may use this cultivator. If 
you loan someone this unit, loan them these instructions 
also.

SPECIFIC SAFETY RULES

Summary of Contents for RY60511B























Reviews: