RYTEC Spiral SST Installation Manual Download

Page: 18 / 36

Spiral

SST and STT Prewire Installation Manual

Spiral

SST and STT Prewire Installation Manual

■

1072124-0

■

Rev 03

■

01/22

How to install the secondary drive belt

Make sure the secondary drive belt is

kept taut throughout these steps.

▪

The belt is preinstalled around the

pulley

▪

The

door panel end bracket

is connected at the

precise height to keep the door panel level.

▪

The belt is kept taut to the pulley and end bracket during
crating by

two cable ties

▪

If the belt becomes loose

before it is secured to the

baseplate, it can skip a tooth in the pulley.

This will cause

the door panel to run crooked and damage the door.

Keep downward pressure

on the secondary drive belt

until the baseplate pulley assembly

is installed and the

belt has been properly tensioned.

Pull

the secondary drive belt and baseplate

pulley assembly out of the console.

Lower

them down the side column.

Grab

the belt below the cable ties and pull

gently downward to keep the belt tight.

Cut

the two cable ties to release the belt.

Remove

the top nut on the front baseplate

mounting post.

Keep

the nut.

Loosen

the top nut on the rear mounting post.

DO NOT loosen

the bottom nuts.

Cutting

pliers

KEEP

REUSE

17mm

Set the height

of the top nut on the rear baseplate mounting post

1: Slide

the rear flange of the baseplate pulley assembly

under the top nut

until it touches the post.

2: Press down

on the front of the pulley assembly as hard as you can

▪

The top nut is at the correct height when

three (3) threads

of the front mounting post clear the front flange.

3: Adjust

the height of the nut as needed to reach the correct height.

Set the tension

of the belt.

1: Replace

the top nut on the front mounting post.

Tighten

the nut to increase the tension on the belt.

2: Grab

the belt as close as possible to the midpoint with one hand.

Press

the front and rear legs of the belt together between your fingers and thumb.

▪

The tension is correct when it requires

considerable effort to bring the legs together.

3: Adjust

the height of the top nut as needed to reach the correct tension.

17mm

KEEP

REUSE

Summary of Contents for Spiral SST





































Search results

Summary of Contents for Spiral SST

Reviews:

Related manuals for Spiral SST

Brands by name

Popular brands

RYTEC Spiral SST, Installation Manual

Search results

Summary of Contents for Spiral SST

Reviews:

Related manuals for Spiral SST

Brands by name

Popular brands