background image

P/N 13772-108

7 of 24

Cirrus Design

Section 9

SR22

Supplements

System Failure and Caution Annunciations

If any of the following failure annunciations occur at low altitude or
during an actual instrument approach, disengage the autopilot,
execute a go-around or missed approach as appropriate. Inform ATC
of problem. Do not try to troubleshoot until a safe altitude and
maneuvering area are reached or a safe landing is completed.

Annunciation

Condition

Action

Flashing RDY for 5 
seconds with 
audible tone.

Autopilot disconnect. All 
annunciations except RDY 
are cleared.

None.

Flashing RDY with 
audible tone then 
goes out.

Turn coordinator gyro 
speed low. Autopilot 
disengages and cannot be 
re-engaged.

Check power to turn 
coordinator.

Flashing NAV, 
REV, or APR.

Off navigation course by 
50% needle deviation or 
more.

Use HDG mode until 
problem is identified. 
Crosscheck raw NAV 
data, compass heading, 
and radio operation.

Flashing NAV, 
REV, or APR with 
steady FAIL

Invalid radio navigation 
signal.

Check Nav radio for 
proper reception. Use 
HDG mode until problem 
is corrected.

Flashing VS

Excessive vertical speed 
error over selected vertical 
speed. Usually occurs in 
climb.

Reduce VS command 
and/or adjust power as 
appropriate.

Flashing GS

Off glideslope centerline by 
50% needle deviation or 
more.

Check attitude and 
power. Adjust power as 
appropriate.

Flashing GS with 
steady FAIL

Invalid glideslope radio 
navigation signal.

Disconnect autopilot and 
initiate go-around or 
missed approach 
procedure. Inform ATC.

Flashing GS plus 
ALT.

Manual glideslope disabled. Re-enable by pressing 

NAV mode button.

Revision 5: 08-15-07

Summary of Contents for System 55X

























Reviews: