Saber Edge LM-21AHD Operator'S Manual Download

Page: 12 / 14

Maintenance

Recommended Maintenance Schedule

Maintenance Service

Maintenance Procedure

After the first 5 hours

• Change the engine oil.

Before each use or daily

• Check the engine oil level.

• Ensure that the engine stops within 3 seconds after releasing the blade control

bar.

• Remove grass clippings and dirt from under the housing

Every 25 hours

• Check the air cleaner for dirty, loose, or damaged parts, and clean or replace

them if necessary.

Every 50 hours

• Change the engine oil.

Every 100 hours

• Replace the air-cleaner element (more frequently when operating the ma-

chine in dusty or dirty operating conditions).

• Clean the cooling system (refer to your engine owner’s manual).

• Replace the spark plug.

Before storage

• Empty the fuel tank before repairs as directed and before annual storage.

Yearly

• Replace the blade or have it sharpened (more frequently if the edge dulls quickly)

by an Authorized Saber Edge Dealer .

• Refer to your Engine Operator’s Manual for any additional yearly mainte-

nance procedures.

Preparing for maintenance

1. Stop the engine and wait for all moving parts to stop.

2. Disconnect the spark-plug wire from the spark plug before performing any maintenance

procedure.

3. After performing the maintenance procedure(s), connect the spark-plug wire to the spark plug.

Important: Before tipping the machine to change the oil or replace the blade, allow the fuel tank to run

dry through normal usage. If you must tip the machine prior to running out of fuel, use a hand fuel pump

to remove the fuel. Always tip the

machine onto its side with the dipstick down.

Warning: Tipping the machine may cause the fuel to leak. Gasoline is flammable, explosive and can

cause personal injury.

Run the engine dry or remove the gasoline with a hand pump, never siphon.

Summary of Contents for LM-21AHD















Search results

Summary of Contents for LM-21AHD

Reviews:

Related manuals for LM-21AHD

Brands by name

Popular brands

Saber Edge LM-21AHD, Operator'S Manual

Search results

Summary of Contents for LM-21AHD

Reviews:

Related manuals for LM-21AHD

Brands by name

Popular brands