background image

1

 

Warning

Read and Follow all safety rules and instructions in this manual before attempting to operate this machine.  

Failure to comply with these instructions may result in personal injury

Operator’s Manual

21” Steel 

Walk Behind Lawn Mower

Thank you for purchasing a Saber Edge Lawn Mower It was carefully engineered to provide excellent  

performance when properly operated and maintained. It is designed primarily for cutting grass on  

well-maintained lawns on residential or commercial properties. It is not designed for cutting brush or for  

agricultural uses.
Before operating your new Saber Edge it is strongly recommended all operators carefully read this manual in 

its entirety before operating the equipment. This manual explains how to operate and maintain the product 

properly and safely to avoid injury and property damage. 
You may contact Saber Edge Corporations directly at www.saberturf.com for product and accessory  

information, help finding a dealer, or to register your product.
Whenever you need service, genuine Saber Edge parts, or additional information, contact an Authorized  

Service Dealer or Saber Edge’s Customer Service and have the model and serial numbers of your product ready.

Saber Edge Corporation  www.saberturf.com

Walk Behind Model : LM-21SBS

Summary of Contents for LM-21SBS













Reviews: