11
–
Place the mower to the side so that the spark plug side is at the top and the waste
oil is drained into a collecting vessel.
Do not drain used oil into the sewage system or soil; dispose of it according
to the local regulations.
–
Put up the mower and fill in brand oil at the connector (for quantity and quality refer to
the technical data). Screw in the dipstick and check the oil level (see
“Checking the
oil level”
and
“Filling with oil”
, figure
Y1
)! If the oil level is correct, insert the
dipstick and tighten it.
Cleaning and replacing the air filter (figure W )
IMPORTANT
Never let the engine start or run whilst the air filter is removed.
–
Loosen the air filter cover lock (4) with a screwdriver from the air filter housing (1)
and remove the air filter cover (3).
–
Remove the filter(s) (2).
–
Clean the filter(s) every 50 operational hours.
In case of minor contamination, tap out gently on a smooth surface. In case of severe
contamination or damage, renew the filter(s). Do not wash out or blast out the paper
filter using compressed air and do not oil it.
–
Insert the filter(s) (2).
–
Attach the air filter cover (3) onto the filter and let the air filter cover lock (4) engage
in the air filter housing (1).
In the case of unfavourable operation conditions (severe formation of dust), cleaning is
required after every mowing job. Replace the air filter annually or every 200 operating
hours.
(For the air filter order number, refer to original spare parts and accessories)
Checking the spark plug (figure Y )
To check for wear, remove the spark plug connector and screw out the spark plug. If the
electrode is badly worn, the spark plug must be replaced as a matter of course (for order
no. see original spare parts list and accessories).
Otherwise it is sufficient to clean the spark plug with a steel brush and set the electrode
gap to between 0.7 and 0.8 mm. Screw the spark plug (pay attention to sealing ring) into
the engine by hand and tighten using the socket wrench. Press on spark plug connector.
Replace the spark plug annually.
Correct winter storage of the engine (or when not used for a long period
of time)
–
Empty the petrol tank and let the engine run until it stops due to lack of fuel.
–
Stop the engine and remove the spark plug connector.
–
Drain the oil as long as the engine is still warm. Fill in fresh oil (for quantity and
quality refer to the technical data).
–
Remove grass and mowing deposits from the cylinder and cylinder ribs, under the
engine cover and around the silencer.
–
Always keep the device in a clean state in a closed, dry room and inaccessible to
children.
19 TROUBLESHOOTING
Faults
Possible causes
Remedy
Pos: 25.3.2 / Innenteil/ Stö rung sursache n und deren Beseitig ung/Störungstabelle nelemente/Motor springt nicht an E- Start 47e r, (fixed speed) 675EXi_4- stellig @ 65\mod_1594304335556_6.docx @ 633442 @ @ 1
Engine does not start
Safety grip not pressed
down.
Press the control bar to
the upper part of the
handlebar
D
.
Fuel tank is empty.
Fill the fuel tank with clean
and fresh fuel.
Spark plug connector
loose.
Press
on
spark
plug
connector or have it checked
by an authorised workshop.
Spark plug defective or
dirty or electrode burnt
out.
Replace or clean the
spark plug, set the electrode
gap
Y
:
0.7
–
0.8 mm
Excessive petrol supply
to engine (spark plug
wet).
Have it checked by an
authorised workshop.
Air filter soiled.
Clean or replace the air filter
insert
W
.
Pos: 25.3.3 / Innenteil/ Stö rung sursache n und deren Beseitig ung/Störungstabelle nelemente/Motorleistung lä sst nach @ 33\mod_1408527299785_6.do cx @ 241496 @ @ 1
Engine
power
decreasing
Air filter soiled.
Clean or replace the air filter
insert
W
.
Spark plug clogged with
soot.
Have it checked by an
authorised workshop.
Fuel old or soiled
Empty the petrol tank and fill
with fresh fuel.
Pos: 25.3.4 / Innenteil/ Stö rung sursache n und deren Beseitig ung/Störungstabelle nelemente/Motor lä uft unregelmäßig @ 0\mod_1127909273145_6.docx @ 1364 @ @ 1
Engine runs irregularly
Air filter soiled.
Clean or replace the air filter
insert
W
.
Spark plug clogged with
soot.
Have it checked by an
authorised workshop.
Pos: 25.3.5 / Innenteil/ Stö rung sursache n und deren Beseitig ung/Störungstabelle nelemente/Mäher fährt nicht (nur be i zuscha ltba rem Fahrantrieb) @ 17\mod _1334237837356_6.d ocx @ 137111 @ @ 1
Mower does not move
(only with connectible
autodrive)
Drive control bar not
pulled up.
Pull the drive control bar up
G
.
Have it checked by an
authorised workshop.
Extreme vibration
Have it checked by an
authorised workshop.
Pos: 25.3.8 / Innenteil/ Stö rung sursache n und deren Beseitig ung/Störungstabelle nelemente/Schnitt unsaube r, Rasen wird gelb, Benzin MU STER @ 17\mod_1331728299135_6.docx @ 134626 @ @ 1
Poor
cutting,
lawn turns yellow
Cutter bar blunt.
Have it reground and
balanced by an authorised
workshop
Q
.
Cutting height too low.
Set higher cutting height
I
.
Engine speed too low.
Have it checked by an
authorised workshop.
Excessive
mowing
speed.
Adjust the mowing speed and
switch off the autodrive, if
necessary.
Mower paths do not
overlap sufficiently.
With high grass, the mowing
paths may possibly have to
overlap more.
Lawn matted.
A noticeable improvement
can be achieved by using
a scarifier.
Pos: 25.3.9 / Innenteil/ Stö rung sursache n und deren Beseitig ung/Störungstabelle nelemente/Auswurf ve rstopf t, Be nzin, TurboSignal MU ST ER @ 17\mod _1331728502002_6.do cx @ 134643 @ @ 1
Ejection blocked
Collecting bag full.
Empty the collecting bag
L
.
Engine speed too low.
Have it checked by an
authorised workshop.
Cutting height too low
and grass too high.
Set higher cutting height
I
.
Excessive mowing speed. Adjust the mowing speed and
switch off the autodrive, if
necessary.
Grass is wet.
Let lawn dry.
The mulched grass
looks
bad:
lumps,
excessive
amounts of cut grass,
coarse cut
Cutter bar blunt.
Have it reground and
balanced by an authorised
workshop.
Mulching
rule
not
followed (cut max. 1/3 of
grass height; the grass
height to be cut must be
less than 10 cm).
Set higher cutting height
I
.
Convert mower to rear
ejection
U2
+
S1
and mow
the lawn with a high cutting
height setting first.
Excessive travel speed.
Adjust the travel speed,
switch off the autodrive,
if necessary.
Grass
accumulation
under the mower.
Set higher cutting height
I
.
Mower paths do not
overlap sufficiently.
With high grass, the mowing
paths may possibly have to
overlap more.
Grass is wet.
Set higher cutting height
I
.
Let lawn dry.
Pos: 25.4 /Innente il/Störungsursachen und de ren Beseitigung/Stö rungsursa chen und dere n Be seitigung Tex t @ 0\mod _1115378183390_6.do cx @ 581 @ @ 1
In case of faults and defects which have not been listed here, please contact the nearest
authorised workshop.
Repairs which require specialised knowledge should only be performed by a qualified
expert. Your authorised workshop will naturally also be glad to help if you do not wish to
perform the maintenance work described here yourself.
Summary of Contents for 40-CLASSIC
