Page # 107
877 1st Ave. N.W. | Sioux Center, IA 51250 | Toll Free: 1.866.722.1488 | siouxautomation.com
OPERATION
REPLACEMENT PARTS
READ complete manual CAREFULLY
BEFORE attempting operation.
877 1st Ave. N.W. | Sioux Center, IA 51250 | Toll Free: 1.866.722.1488 | siouxautomation.com
OPERATION
REPLACEMENT PARTS
READ complete manual CAREFULLY
BEFORE attempting operation.
.38
.25
.13
.06
IN THIS AREA
PLACE SHIMS
FLANGE
AUGER TUBE
TO CENTER
PLACE SHIMS
IN THIS AREA
TO CENTER
AUGER TUBE
FIGURE B
SCALE: 1:12
FIGURE D
FOR TWIN AUGER MODELS,
LEADING EDGES OF AUGERS
SHALL BE IN LINE WITH EACH OTHER
ANGLE BLADE
INSIDE OF MIXER WALL
FIGURE C
SCALE: 1:8
LEADING EDGE
OF BOTTOM
AUGER FLIGHT
PROJECTION
ENG.
D
C
B
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
A
1
FINISH
MANUFACTURING PROCESS
SURFACE AREA
GENERAL TOLERANCES
SIZE
WEIGHT
1
SIOUX AUTOMATION CENTER, INC
E NW, SIOUX CENTER, IA 51250
1
877 F
SPECIFIED
DATE
DFTM.
AP
IN
1-15
IRST AV
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF SIOUX AUTOMATION CENTER, INC. ANY REPRODUCTION
.
SAC MATERIAL
2
SCALE
DWG. NO.
B
REV.
MATERIAL DESCRIPTION
KIT,3675,BASE,TRK
WITH CORRECT AUG ASSY
-
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF SIOUX AUTOMATION CENTER, INC. IS PROHIBITED.
TOLERANCES UNLESS
DIMENSIONS ARE IN INCHES
AS NOTED
LBS
ANGULAR
.005
1:12
SHEET
OF
1
.XX = .03
.XXX =
THIRD ANGLE
DATE
SCALE: 1:12
INSIDE LEADING EDGE
FIGURE A
PLACE SHIMS
UNDER TUBE
OUTSIDE LEADING EDGE
.31
.19
.38
.25
.13
.06
IN THIS AREA
PLACE SHIMS
FLANGE
AUGER TUBE
TO CENTER
PLACE SHIMS
IN THIS AREA
TO CENTER
AUGER TUBE
FIGURE B
SCALE: 1:12
FIGURE D
FOR TWIN AUGER MODELS,
LEADING EDGES OF AUGERS
SHALL BE IN LINE WITH EACH OTHER
ANGLE BLADE
INSIDE OF MIXER WALL
FIGURE C
SCALE: 1:8
LEADING EDGE
OF BOTTOM
AUGER FLIGHT
PROJECTION
ENG.
D
C
B
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
A
1
FINISH
MANUFACTURING PROCESS
SURFACE AREA
GENERAL TOLERANCES
SIZE
WEIGHT
1
SIOUX AUTOMATION CENTER, INC
E NW, SIOUX CENTER, IA 51250
1
877 F
SPECIFIED
DATE
DFTM.
AP
IN
1-15
IRST AV
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF SIOUX AUTOMATION CENTER, INC. ANY REPRODUCTION
.
SAC MATERIAL
2
SCALE
DWG. NO.
B
REV.
MATERIAL DESCRIPTION
KIT,3675,BASE,TRK
WITH CORRECT AUG ASSY
-
IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF SIOUX AUTOMATION CENTER, INC. IS PROHIBITED.
TOLERANCES UNLESS
DIMENSIONS ARE IN INCHES
AS NOTED
LBS
ANGULAR
.005
1:12
SHEET
OF
1
.XX = .03
.XXX =
THIRD ANGLE
DATE
SCALE: 1:12
INSIDE LEADING EDGE
FIGURE A
PLACE SHIMS
UNDER TUBE
OUTSIDE LEADING EDGE
.31
.19
AUGER ASSEMBLIES
INSTALLING REPLACEMENT AUGERS:
STEP 1 - REMOVE OLD AUGER.
STEP 2 - CUT FLANGES AND ANGLE BLADE OFF OF THE TOP SURFACE OF BOTTOM FLIGHT. (THESE PARTS ARE TACK WELDED HERE FOR
SHIPPING PURPOSES.) REMOVE THE AUGER COVER PLATE AND SET ASIDE FOR NOW.
STEP 3 - TIGHTLY BOLT FLANGES TO THE TOP OF THE GEARBOX. REFER TO FIGURE B.
NOTE: NOT ALL GEARBOXES WILL LOOK LIKE THIS NOR ARE THEY ALL THE SAME HEIGHT INSIDE THE TUBE, BUT THEY ALL HAVE A
FLAT AREA THAT THE FLANGES WILL BOLT TO.
STEP 4 - PLACE THE AUGER OVER THE GEARBOX AND AROUND THE FLANGES. SHIMS NEED TO BE PLACED UNDER THE AUGER TUBE
(IN AT LEAST 3 PLACES) SUCH THAT THE INSIDE LEADING EDGE OF THE BOTTOM AUGER FLIGHT IS LOCATED AT .19 TO .31 INCHES
FROM THE FLOOR OF THE MIXER. REFER TO FIGURES A AND B.
STEP 5 - PLACE SHIMS IN BETWEEN THE OD OF THE FLANGES AND THE ID OF THE TUBE IN AT LEAST 3 LOCATIONS. (REFER TO FIGURE B.)
THIS WILL CENTER THE AUGER TUBE ON THE FLANGES. TACK WELD THE FLANGES TO THE TUBE.
STEP 6 - REMOVE THE SHIMS FROM UNDER THE AUGER TUBE AND ROTATE THE AUGER 360 DEGREES TO VERIFY THAT THE INSIDE LEADING
EDGE OF THE AUGER IS .19 TO .31 INCHES ABOVE THE FLOOR THROUGH THE FULL ROTATION OF THE AUGER. IF THIS CLEARANCE
IS NOT MAINTAINED, READJUST THE SHIMS AND REMOVE AND REPLACE THE TACK WELDS ON THE FLANGES AS NECESSARY.
STEP 7 -ONCE AGAIN, REMOVE THE SHIMS FROM UNDER THE AUGER TUBE AND ROTATE THE AUGER 360 DEGREES CHECKING TO ENSURE THAT
THE .19 TO .31 INCH CLEARANCE WITH THE FLOOR IS MAINTAINED. PLACE A SOLID FILLET WELD AT THE CONNECTION OF THE
FLANGES TO THE ID OF THE AUGER TUBE. IF THERE IS TOO MUCH OR TOO LITTLE CLEARANCE AT THE OUTSIDE LEADING EDGE OF
THE BOTTOM AUGER FLIGHT, THE FLIGHT MAY NEED TO BE PHYSICALLY MANIPULATED. IF THIS IS REQUIRED, CONTACT THE SIOUX
AUTOMATION CENTER SERVICE DEPARTMENT FOR GUIDANCE.
STEP 8 -LOCATE THE ANGLE BLADE (SHOWN IN FIGURE C) ON THE TOP SURFACE OF THE BOTTOM AUGER FLIGHT. TAKE ALL MEASUREMENTS
FROM THE VERTICAL SIDEWALL OF THE MIXER. TACK WELD IN POSITION.
NOTE: THE ANGLE BLADE MUST BE PERPENDICULAR TO THE BOTTOM AUGER FLIGHT.
STEP 9 -ROTATE THE AUGER 360 DEGREES TO ENSURE THE ANGLE BLADE DOES NOT CONTACT ANY PART OF THE MIXER WALLS. IF THE ANGLE
BLADE CONTACTS ANYTHING, REMOVE THE TACK WELDS AND ADJUST THE BLADE POSITION AS NECESSARY. ONCE THE AUGER CAN
BE ROTATED WITHOUT THE ANGLE BLADE MAKING CONTACT WITH ANYTHING, WELD THE BLADE FULLY IN PLACE.
Summary of Contents for 3600 Series
Page 129: ...MAINTENANCE RECORD...
Page 130: ...MAINTENANCE RECORD...
Page 131: ...MAINTENANCE RECORD...
Page 134: ......
