background image

 

SAFETY FIRST 

 

 

FARM AND INDUSTRIAL EQUIPMENT INSTITUTE SAFETY ALERT SYMBOL

 
 

This symbol is used preceding all 

CAUTION

 (a general safety  

 reminder), 

WARNING

 (denotes a potential hazard), and 

DANGER

  

 

(denotes a potential injury) notices! 

 
Most farm accidents, like industrial, home, and highway accidents are caused by the failure of some 
individuals to observe simple and fundamental safety rules or precautions.  For this reason, farm 
accidents, just as other types of accidents, can be prevented by recognising the causes of accidents and 
doing something about them before an accident occurs. 
 
Regardless of the care used in the design and construction of farm equipment, there are many points 
that cannot be completely safeguarded without interfering with accessibility and efficient operation. 

 

A CAREFUL OPERATOR IS THE BEST INSURANCE AGAINST AN ACCIDENT 

 

The complete observance of one simple rule would prevent many thousand serious injuries each year.  
That rule is 

"

NEVER ATTEMPT TO CLEAN, OIL, OR ADJUST A MACHINE WHILE IN 

MOTION". 

NATIONAL SAFETY COUNCIL 

 

 

BEFORE ATTEMPTING TO OPERATE YOUR NEW MACHINE, BE SURE TO READ 
THIS OWNERS MANUAL AND FAMILIARIZE YOURSELF WITH THE MACHINE!!  
OBSERVE THE FOLLOWING PRECAUTIONS FOR SAFE OPERATIONS OF THIS 
MACHINE!! 

 

 

SAFETY TIPS: 

1.  Keep Hands, Feet, and Clothing away from PTO Shaft! 
2.  DO NOT Climb on or enter Machine while in operation. 
3.  DO NOT Make High Speed Maneuvers with the machine. 
4.  Disengage PTO and remove Keys before servicing. 
5.  Keep ALL Shields in place.  
6.  DO NOT allow riders on outside of vehicle. 
7.  DO NOT attempt to clean, oil or adjust machine while in motion. 
8.  DO NOT exceed rated PTO RPM speed. 

Summary of Contents for MaxiMixer 2050






















































Reviews: