Ver 1.0
10
6.1.3 Visualizaciones y configuraciones asistencia técnica (botones de acceso MODE &
SET & +)
6.1.3.1
tB: Configuración del tiempo de bloqueo por falta de agua (valor preconfigurado 10s)
La configuración del tiempo de espera del bloqueo por falta de agua permite seleccionar el tiempo (en
segundos) utilizado por el sistema PWM para señalar la falta de agua de la electrobomba.
La modificación de este parámetro puede ser útil si se conoce un retardo entre el momento en que la
electrobomba se enciende y el momento en que comienza efectivamente el suministro. Un ejemplo puede
ser aquel de una instalación donde la tubería de aspiración de la electrobomba es muy larga y puede tener
alguna pequeña pérdida. En este caso, podría suceder que la tubería en cuestión se vacíe, incluso si no
falta agua, y que la electrobomba tarde un cierto tiempo para recargarse, suministrar flujo y presurizar la
instalación.
6.1.3.2
GP: Configuración de la ganancia del coeficiente proporcional del PI
Para mantener constante la presión en la instalación, el sistema PWM realiza un control tipo PI en el error
de presión detectado. Según este error, el PWM calcula la potencia a suministrar a la electrobomba. El
comportamiento de este control depende de los parámetros GP y GI configurados. Para solucionar
diferentes comportamientos de los diferentes tipos de instalaciones hidráulicas donde el sistema puede
funcionar, el PWM permite seleccionar parámetros diferentes de aquellos configurados en fábrica.
Para la mayoría de las instalaciones, los parámetros GP y GI de fábrica son aquellos ideales.
Si se
produjeran problemas de regulación, dichas configuraciones pueden modificarse.
Por lo general, el valor proporcional debe aumentarse para sistemas caracterizados por elasticidad (tuberías
de PVC y amplias) y disminuirse en las instalaciones rígidas (tuberías de hierro y estrechas)
6.1.3.3
GI: Configuración de la ganancia del coeficiente integral del PI
Indicativamente se puede afirmar que la presencia de grandes caídas de presión, al aumentar
repentinamente el flujo, o una respuesta lenta del sistema, pueden compensarse aumentando el valor de GI.
Por el contrario, al producirse “vibraciones” en la presión (oscilaciones de presión muy rápidas alrededor del
valor de setpoint) puede eliminarse disminuyendo el valor de GI.
Nota:
Un ejemplo típico de instalación donde esto puede suceder es aquel donde la tubería de
aspiración de la electrobomba es muy larga. En este caso se puede provocar una
elasticidad hidráulica que influya sobre el control PI y, por lo tanto, sobre la regulación de la
presión.
Importante:
Para obtener regulaciones de presión satisfactorias, por lo general hay que modificar GP y
GI. En efecto, la combinación justa entre estos dos parámetros permite la regulación ideal
de la presión.
6.1.3.4
FS: Configuración de la frecuencia máxima de rotación (valor preconfigurado 50Hz)
Para obtener potencias hidráulicas mayores, el motor de una electrobomba puede funcionar con un valor de
frecuencia superior al valor nominal. La sobrealimentación de la electrobomba es útil para cubrir altas
demandas de flujo sin que la presión de la instalación sea muy diferente de aquella configurada. Esta
condición de funcionamiento no puede durar mucho tiempo porque provoca el aumento de la temperatura
del motor que podría arruinarse.
Para aprovechar la sobrealimentación, el PWM permite configurar una frecuencia máxima de servicio
superior a la frecuencia nominal, creando una imagen térmica del motor instalado y limitando la frecuencia
máxima enviada a la electrobomba si la temperatura aumentara mucho. El valor de la frecuencia máxima
configurada (FS) se logra con el motor frío y disminuye hasta 50Hz al aumentar la temperatura de los
bobinados.
Por otra parte, si fuera necesario, el PWM permite configurar una frecuencia máxima de servicio inferior a la
frecuencia de 50 Hz hasta un mínimo de 40Hz. En este caso, en cualquier condición de regulación, la
electrobomba no será nunca alimentada con una frecuencia superior a aquella configurada.
6.1.3.5
dP: Configuración del diferencial de presión con flujos bajos (valor preconfigurado 0)
En modalidad 1, la configuración de la excursión admitida para el setpoint de presión permite seleccionar un
intervalo de presiones inferior al setpoint (SP) con las que el PWM regulará en caso de flujos bajos.