DRAINAGE
82
PROGRAMMING THE MACHINE
81
Important: It is advisable to drain the
machine before the first start, after a
prolonged period the machine has not
been used or whenever the water
tank has been completely emptied.
Furthermore, should the pump be defective, the
display shows:
"VENTILATE "
Programming the machine
32
To enter the programming mode, press the key
ENT
(
pre-ground coffee) when the machine
is on and keep it pressed until the first two lines
of the programming mode are displayed:
"1 LANGUAGE "
"2 SYSTEM 2 "
At the end of the line a blinking asterisk is
displayed, which can be moved up and down
with the keys
(tall and regular coffee).
If the asterisk is on the first menu, press
button
to move it on the second menu and vice versa.
The display shows the following sequence of
messages:
1 LANGUAGE
10 PROG. H. WATER
2 SYSTEM 2
11 PROG. CAPPUC.
3 WATER HARDN.
12 TOTAL COFFEE
4 CUP HEATER
13 DESCALING
5 TEMP. L. COFFEE
14 SIGN. DESCAL.
6 TEMP. COFFEE
15 TIMER
7 TEMP. S. COFFEE
16 VENDING
8 PREBREWING
17 EXIT
9 PREGRINDING
To leave the menu, move the asterisk at the end
of the line to item <<
Exit
>> using the key
.
Then, press
ENT
( pre-ground coffee). The
machine is now in the normal mode again.
Selecting single menus
Select the different menu items by means of the
keys
. The key
ENT
allows you to activate the
selected item. It is possible to modify the selected
figures in a menu item using the keys
. The key
ENT
memorizes the selected options (for instance
“
ON
” for the cup heating plate).
Should you accidentally change some data,
press
ESC
(*…) to leave the menu item without
saving the new options which were selected
accidentally.
Language selection
Move the asterisk to the menu item
“
LANGUAGE
” using the keys
. Press
ENT
to activate this item. The following message
will be displayed:
"1 LANGUAGE "
"ENGLISH "
The keys allow you to change the set options :
“
ENGLISH
” , “
ITALIANO
” , “
FRANÇAIS
”,
“
DEUTSCH
” , “
NEERLANDAIS
”, “
ESPAÑOL
”,
“
PORTUGUES
”.
Enabling of second heating system
Royal Cappuccino is equipped with two boilers
with independent circuits. One of these boilers
can be disconnected. By pressing
keys
move the asterisk at the end of the
line to the menu item “
SYSTEM 2
”. Press
ENT
to activate this item. The following message will
be displayed:
"2 SYSTEM 2 "
"ON "
The keys
allow you to change the set
options:
ON, OFF.
If the second boiler is disconnected it is not
possible to dispense steam and therefore cap-
puccino can’t be prepared. Should the cappuc-
cino selection button be pressed
or the steam/hot water knob be opened, the
display shows the following message:
"PLEASE ACTIVADE "
"SYSTEM 2 "
Water hardness adjustment
In order to adjust the water hardness, it is necessary
to test the water using the strip supplied with the
machine. Dip the strip into the water for a second,
shake off excess water gently, wait approx. 1
minute and read the results.
Move the asterisk at the end of the line to the
menu item “
WATER HARDN.
” using the keys
and select it by means of the
ENT
button.
The following message will be displayed:
"3 WATER HARDN./ "
"HARDNESS 3 "
The keys
allow you to change the set
options:
HARDNESS 4
(hard water)
HARDNESS 3
(medium water)
HARDNESS 2
(soft water)
HARDNESS 1
(very soft water)
Cup heating plate connection
Royal Cappuccino is equipped with a useful cup
heating plate which can be disconnected, if
required.
Press keys
to move the asterisk to item
“
CUP HEATER
”. Press
ENT
to activate this
function.
The following message will be displayed:
"4 CUP HEATER "
"ON "
31
Install the water tank, slightly pressing over it to
fit the valve which will open automatically.
Do not fill the tank with an excessive quantity of
water.
Always fill the tank with fresh water only: hot
water as well as other fluids might damage the
tank. Never use carbon dioxide added water.
Do not switch on the machine on if the water tank
is empty: always make sure there is enough
water in the tank!
Connect the plug to the socket and press the main
switch. The following message will be displayed:
"WARMING UP......."
Should
"ENERGY "
"SAVING "
be displayed, press button
“Standby” to
disactivate the energy saving mode.
Drainage
Direct the steam/hot water spout on the drip tray
(2). Place a cup or another suitable container
under the dispensing tube, then turn the steam/
hot water knob counterclockwise. The pump
starts automatically. Wait until a regular water jet
is obtained, then close the knob. The machine is
now drained and ready to work.
The following message will be displayed:
"SELECT PRODUCT "
"READY FOR USE "
Hardness 4
Hardness 3
Hardness 1
Hardness 2
