Assemble the grind ring support and make sure
the blue marks coincide.
50
Turn the adjustment ring clockwise, to make the
red marks coincide.
51
Fit the adjustment lever on the ring, until it
coincides with the previously set grinding degree.
Cappuccinatore
52
To quickly clean the cappuccinatore, immerse
the suction pipe into warm water and let water
flow through it.
For a more accurate cleaning, remove the
cappuccinatore and open cover (29). Clean the
outside part with warm water and rinse it with
cleaned water.
Descaling
Attention: The descaling operations mus
be carried out when the machine
components are cold.
Descaling removes limescale from all surfaces
and holes, thus ensuring a perfect operation of
valves, heating controls and other important
parts.
Note:
due to the complexity of the coffee
machine hydraulic circuit, the following descaling
cycles (automatic and standard) do not allow the
descaling of all tubes.
In fact, easily accessible components
such as the central unit (22) and its
plastic connection are excluded.
The machine must be descaled every 3-4 months,
depending on the water hardness degree.
A more frequent descaling is recommended
wherever the water hardness degree is very high.
To avoid dangerous delays to users, this machine
is supplied with a special control counter,
reminding the user to perform this operation,
according to the water hardness degree.
91
CLEANING AND MAINTENANCE OPERATIONS
DESCALING
92
to the special electronic protection system.
Important:
Do not start the machine before
the foreign body has been removed, otherwise
the motor may be damaged. Procedures: see
page 92, points 45-49.
Cleaning and maintenance operations
General cleaning
To ensure a good coffee quality and a longer
working life, always keep the machine clean.
Before cleaning the machine, turn off the main
switch, unplug the machine and wait until it
cools down.
Do not immerse the machine into water or other
fluids: it may be irreparably damaged!
Do not wash parts of the machine in the
dishwasher!
Always handdry all parts of the machine, do not
dry them in the oven or microwave oven!
Water tank, drip tray, coffee grounds
container and coffee dispenser
39
In order to keep the service area and the central
unit (22) clean, daily empty the coffee grounds
container (1), after machine use.
The water tank (11), drip tray (2), cup holder grill
(3) and coffee grounds container (1) should be
washed periodically, using a non-abrasive solvent
and drying them carefully.
40
Coffee dispenser (4) may be removed for cleaning
operations. Unloose the screws and rinse the
dispensing tube thoroughly with hot water.
From time to time, clean the machine casing with
a damp cloth and dry it.
Clean pre-ground coffee container (14) with the
aid of the brush supplied, whenever necessary.
Central unit
Clean central unit (22) whenever the coffee
bean container is filled, or at least once a week.
Switch off the machine and open service door
(19). Remove grounds coffee container (1).
41
Remove central unit (22), by holding the handle
and shortly pressing the PRESS key.
Wash the central unit with hot water;
do not
use any solvent.
42
Make sure there are no coffee residues on the
two steel filters: the upper filter can be removed
by unloosening and turning the plastic pin
anticlockwise using the tool supplied.
Dry thoroughly each central unit component, fit
the filter again and tighten it properly with the
screw .
43
Remove coffee rest drawer (23) and clean it,
using a non-abrasive solvent.
Clean the service area thoroughly and fit the
coffee rest drawer again.
44
By holding the central unit by its handle, slide it
back into its original position, making sure it is
correctly engaged. Then close the door. Fit the
coffee grounds container again.
When fitting the central unit, do not
press “PRESS” button: it may cause
irreparable damages to the machine!
Warning:
if the central unit is not correctly
fitted, the following message will be displayed:
"BREW UNIT MISS "
The machine cannot dispense coffee.
Coffee grinder
Never fill the coffee grinder with water: it may
irreparably damage the machine!
45
Clean the coffee beans container periodically;
this operation should be accomplished
by a qualified technician!
Unplug the
machine.
Empty the coffee container and unloose the two
fastening screws. Now, the container can be
removed and cleaned.
46
Carefully pull the adjustment lever upwards,
previously writing the set grinding degree.
47
Turn the adjustment ring counterclockwise, until
the blue marks coincide.
48
Now, it is possible to remove the grinding ring
from the machine, slightly pulling it upwards.
49
With the aid of a brush or a narrow vacuum
hose, clean both the gear box and the grind ring
support.
Make sure the position of the grind ring does not shift.
To reassemble the coffee grinder, carry out the
reverse sequence, making sure the adjustment
ring has not been shifted during cleaning. If that
is the case, turn it until the blue mark coincide
with one of the three notches.
