English
9
56
DISPLAY
Description
3.3.
This is the order in which the products making up the beverage are brewed.
Beverage
1
…
The possible choices are:
3.3.
0 =does not dispense any product
Beverage
1
1 = dispenses product 1
Sequence
0C00
2 = dispenses product 2
3 = dispenses product 3
4 = dispenses product 4
5 = dispenses product 5
6 = dispenses product 6
7 = dispenses product 7
8 = dispenses product 8
C = dispenses coffee beans from coffee hopper no. 2
K = dispenses coffee beans from coffee hopper no.1
W = dispenses hot water
S1 = dispenses syrup product 1 (optional)
S2 = dispenses syrup product 2 (optional)
Consequently, the combination of “3C00” or “30C0” or “03C0” will always dispense
product 3 and coffee beans. The settings of products making up the beverage will be
requested according to the sequence.
Important
To obtain the cup only, set beverage sequence to 0000 and block sugar regulation (sugar
setting = “sugar blocked”).
3.3.
This defines the quantity of coffee to be brewed.
Beverage
1
The quantity of dispensable coffee can be adjusted from “1” to “999”.
H2O / Coffee
38
3.3.
Defines the amount of hot water to be dispensed.
Beverage
1
Just water
101
3.3.
It determines the instant powder delivery rate.
Beverage
1
The value can be set between 10 and 100. The lower the value the smaller the powder
delivery rate.
% Instant product
3:50
3.3.
It determines the water delivery rate.
Beverage
1
The value can be set between 20 and 100. The lower the value the smaller the water
delivery rate.
% Pump
3:50
Important
The % pump parameter is displayed only on the machines without instant product boiler.
If the sequence includes several instant products, the sequence “INSTANT PRODUCT - WATER -
DELAY INSTANT PRODUCTS - % OF INSTANT PRODUCT” will be shown again.
If the setting relative to the instant product (“INSTANT PRODUCT - WATER”) means that
the powder dispensing lasts longer than the water dispensing, the vending machine stops
powder dosing (to avoid insufficient rinsing of the mixer) and emits a beep. Readjust the set
parameters in order to have a correct dispensing procedure, i.e. the powder dispensing
should stop a few seconds before the water stops flowing out. This is intended to allow
correct mixer washing.
3.3.
This defines the quantity of instant product to be brewed.
Beverage
1
Instant Dose
3:005
Example: “005” quantity indicates that the motor of the instant product 3 will be activated
for 5 tenths of a second. The quantity of instant product is adjustable from “1” to “100” in
steps of 1. Brewing of the instant product does not occur when the parameter is set at
“0000” (in this case water is brewed).
3.3.
It defines the amount of water to be mixed with the instant powder.
Beverage
1
H2O / instant
product
3:022
Example: “3” indicates that water will be mixed with the instant product 3. “022” indicates that 22 units of water
will be brewed with the instant product. The reference unit is preset by the manufacturer. The amount of water
can be adjusted from ‘“1” to “999” in steps of 1.
Summary of Contents for Atlante 500
