23
START-UP
4
INSTALLMENT
For personal safety follow the “Safety
regulations” found on Par.3.
4.1 Packaging
The original packaging has been designed
to protect the appliance during
transportation.
You are recommended to keep it for later
use.
4.2 Installment requirements
Before installing the machine read the
following safety instructions carefully:
• Locate the machine in a safe place;
• Make sure that it is out of the reach of
children;
• Do not place the machine on a hot
surface or near a naked flame.
The coffee maker is now ready to be
connected.
4.3 Connecting the appliance to the
power supply
Electricity can be dangerous, so
always follow the safety
regulations carefully.
Never use a faulty cable.
Faulty plugs and cables must be
changed immediately by authorised
personnel.
The coffee maker must be connected to a
suitable wall socket.
The voltage of the appliance has been
factory-set.
The voltage on the rating plate (positioned
on the bottom of the appliance) must
correspond to that of your house electricity
supply.
• Uncoil a length of cable from the cable
wind found underneath the appliance,
sufficient for the plug to reach the wall
socket.
• Check that the main switch is in the “0”
position before inserting the plug in the
wall socket.
• Plug the appliance into a wall socket
carrying the correct voltage.
4.4 Filling the water tank
•
Remove the water tank lid (2).
• Take out the water tank (1) by lifting it.
The valve on the bottom of the tank will
not allow water to flow out.
•
Rinse and fill the tank with fresh water
without overfilling.
•
Put the tank back in its correct
position.
• When the tank is in place, press lightly
down on it to insert the valve correctly.
The valve will open automatically.
• Put the lid back on the tank.
Always fill the tank with fresh, not
carbonised water: hot water or
other liquids may damage the tank.
Do not use the coffee maker without
water, always check that there is
enough water in the tank.
4.5 Priming
Before using the machine for the first
time, after the appliance has been left
unused for a long period or when the water
and steam have run out, it is necessary to
prime the machine.
• Turn on the main switch (3), the light on
the inside will be on.
• Point the steam tube (“Pannarello”) over
the drip tray.
• Open the “hot water/steam” knob (6),
turning it in an anti-clockwise direction
Summary of Contents for SIN 007
