background image

XL-AS20016BM-en-US Rev A · 2015-05-28 · Amendments and Errors Reserved · © SAF-HOLLAND, Inc., SAF-HOLLAND, HOLLAND, SAF,  

and logos are trademarks of SAF-HOLLAND S.A., SAF-HOLLAND GmbH, and SAF-HOLLAND, Inc.

Operation Instructions

14

8.   Lift and push the pull arm handle from the disengaged  

position 

(Notch 2 - Figure 23)

 to the engaged 

position 

(Notch 1 - Figure 24)

NOTE:

  If the slider is equipped with an air release pin 

mechanism, push the air release control valve 
knob to engage the lock pins.

9.  Visually check that the lock pins are fully engaged and 

extend through the holes in the upper rail 

(Figure 25)

.

An unsecured slider box can cause loss 
of vehicle control which, if not avoided, 
could result in death or serious inury.

10.  Visually check that the manual stop bar is properly installed  

directly behind slide box 

(Figure 25)

Failure to properly install or position the 
manual stop bar could result in improper 
trailer load distribution which, if not 
avoided, could result in damage to the 
suspension or trailer parts.

MANUAL 
STOP BAR

LOCK PINS 
ENGAGED  
IN SLIDER RAIL

Figure 25 

PULL ARM 
HANDLE

LOCK PINS 
ENGAGED

ENGAGED POSITION

NOTCH 1

NOTCH 2

Figure 24 

Figure 23 

PULL ARM 
HANDLE

DISENGAGED POSITION

NOTCH 1

NOTCH 2

LOCK PINS 
DIS-ENGAGED

CBX 40 ILLUSTRATED

Summary of Contents for CBX 4215.5





















Reviews: