background image

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability 
(the “Prime Design Limited Warranty”). 

 TM & © 2021 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608, 10501022 AND OTHER PATENTS PENDING

5

#3

#5

AAL-8009 

ASSEMBL

Y INSTR

UCTIONS–A

CCESS LADDER

3.2

Slide the Lower Mounting 

Bracket Hanger Rods into 

the Hanger Rod Clamps. 

3.4

Do not tighten until 

Steps 4.5-4.8

This Lower Mounting 

Hanger Rod comes from 

the factory pre-assembled. 

 

It is necessary to remove 

the tightening hardware 

for installation into the 

Hanger Rod Clamps as 

seen in Step 3.2

3.1

LOWER MOUNTING HANGER RODS

3.3

Reinstall Hanger Rod 

hardware removed 

during Step 3.1

Push the Lower Bracket 

down until the Bracket 

Plate stops, and torque

Bolts to 90 in-lb.

2.5

2.4

Assemble the right side Lower Bracket to the Ladder using the 

indicated hardware. The bolts must screw into bolt holes #3, 

and #5 of the Hanger Connector. Repeat Step 2.2 to attach the 

right side Lower Bracket.

Summary of Contents for PRIME DESIGN AAL-8009









Reviews: