background image

www.spearheadbikes.co.uk

KPF0675 
SFSM001_E 
KPF0680       
KPF0684      
KPF0682       
SFSM001_D    
KPF0681       
SFSM001_F
KPF0676    

No.

Qty

Code

Description

BASE PANEL
REAR LH SIDE PANEL
REAR RH SIDE PANEL
BACK FASCIA PANEL
BACK PANEL
FRONT LH SIDE PANEL
FRONT RH SIDE PANEL
FRONT FASCIA PANEL
ROOF PANEL



3
   


6
 
7
8      

x  1     
x  1           
x  1     
x 1    
x  1      
x  1   
x 1 
x 1
x 1

SFSM001_A
KPF0687
KPF0688
SFSM001_001
KPF0338
NBW4013 
NBW7000
KPF0397

DOOR ASSEMBLY
RAMP
SOCKET ATTACHMENT
FLOORING
ROOF BRACKETS
SELF TAPPER SCREWS
COUNTER SUNK SCREWS
PACKING PIECES

10
11
12
13
 
14   
15 
16   
17

x 1
X1
x 1
x 2
x 20
x 122
x 12
x 10

No.

Qty

Code

Description

SELF ASSEMBL

Y INSTRUCTIONS

Before Assembly

It is important you have a level firm 

base for your unit. This should be 

constructed from concrete, tarmac 

or flags and be a minimum of 50mm 

(1.9”) deep.

Stor Measurement 

1012mm x 2055mm 

(40” x 81”)

Minimum base measurement 

1250mm x 2300mm

 (49” x 91”)

Recommended:

Powerdriver

Silicone Sealant

Door Alignment and Placement

If you need the door to open on the reverse side this can be achieved by switching the back 

panel with the door panel, this will result in the door handle being upside down.

Once assembly is completed following the guide provided, it is necessary to correctly level 

the unit using the packing pieces supplied. 

Slide the packing pieces under the corners of the units base as required until an equal gap 

has been achieved around the doors allowing smooth operation. 

Sealant

If required joints can be sealed with sealant. Apply a bead of sealant along the panels at each 

stage. Wipe away any excess sealant immediately with a damp cloth.

YOU WILL NEED

USI 026 21-04-2016

RECORD YOUR 
KEY NUMBER HERE:

Please note: 

Part 12 the Electric Socket attachment can be fitted on the LH side of the unit by removing two screws from the side 

panels. It is compatible with BSS733 single pattresses 60.2mm and twin pattresses 120.6mm. This allows for charging inside the unit. 

When building your unit on a holiday park please check regulations on electricity to outdoor units first.

9

4

5

12

1

3

13

7

10

11

8

6

2

15

16

17

14

Summary of Contents for Skipton SFSM001






Reviews: