Pestillo:
1
Corte cuidadosamente la plantilla por la línea llena y
perfore los dos agujeros
X
.
2
Haga una línea en la plantilla con el enganche, de
manera que la línea punteada esté a nivel con el borde
delantero de la abertura del armario. Fije la plantilla al
armario con la cinta adhesiva (Figura 2).
3
Cierre la puerta/cajón del armario y marque los bordes
exteriores de la plantilla en la puerta/cajón del armario
y en el borde superior de la plantilla (Figura 3). Quite
la plantilla.
4
Line the template up between the two marked edges
on the cabinet door/drawer with the marked lines on
the top edge of the cabinet door/drawer and tape
(Figure 4).
5
Mark the template hole locations on the cabinet door/
drawer. Remove the template and predrill holes with
a 1/16” (1.5mm) drill bit.
6
Secure latch tightly with screws.
NOTE: Cabinet door/drawer should not open more
than 2” (5.08cm).
Latch:
1
Carefully cut template at the solid line and punch out
the two holes
X
.
2
Line the template up with the catch so that the
dotted line is flush with the front edge of cabinet
opening. Tape template to cabinet (Figure 2).
3
Close the cabinet door/drawer and mark the outer
edges of the template on the cabinet door/drawer
and top edge on the template (Figure 3). Remove the
template.
To Install
Para instalar
2
1. Line up catch to the front edge of
the door/drawer opening.
2. Mark the hole locations.
3. Cut out installation template from
instructions.
4. Punch out hole locations.
5. Tape template to cabinet lining
up dotted line with top edge of
cabinet opening.
6. Close cabinet door/drawer.
7. Mark top edge of door/drawer on
the template. Also mark the width
of the template on the door/drawer.
8. Open door/drawer. Remove
template from base of cabient and
retape onto the inside of the
door/drawer.
9. Position the template onto the
inside of the door/drawer lining up
the pencil marks.
10. Mark hole locations.
11. Predrill holes with X” drill bit.
Fron
t edge of cabinet opening
Front edge of cabinet
opening
Front edge of cabinet opening
Front edge of cabinet opening
4
Haga una línea en la plantilla entre los dos bordes
marcados en la puerta/cajón del armario con las líneas
marcadas en el borde superior de la puerta/cajón del
armario y fije con cinta adhesiva (Figura 4).
5
Marque las ubicaciones de los orificios de la plantilla en
la puerta/cajón del armario. Quite la plantilla y perfore
los orificios con una broca de 1/16” (1.5 mm).
6
Fije el pestillo firmemente con tornillos.
NOTA: No se tendría que abrir la puerta/cajón del
armario más de 2” (5,08 cm).
1
1. Line up catch to the front edge of
the door/drawer opening.
2. Mark the hole locations.
3. Cut out installation template from
instructions.
4. Punch out hole locations.
5. Tape template to cabinet lining
up dotted line with top edge of
cabinet opening.
6. Close cabinet door/drawer.
7. Mark top edge of door/drawer on
the template. Also mark the width
of the template on the door/drawer.
8. Open door/drawer. Remove
template from base of cabient and
retape onto the inside of the
door/drawer.
9. Position the template onto the
inside of the door/drawer lining up
the pencil marks.
10. Mark hole locations.
11. Predrill holes with X” drill bit.
Fron
t edge of cabinet opening
Front edge of cabinet opening
Front edge of cabinet opening
Front edge of cabinet opening
3
4
To Clean
Para limpiar
Wipe clean. Keep lock dry.
Limpie con un paño. Mantenga la traba seca.
To Use
Para Usar
1
When drawer is opened 2” the latch
will engage catch. Press down on latch
with finger to open.
NOTE: Latch may be difficult to access
if used on a top drawer that has a
counter top with a 1” overhang. If latch
is difficult to access, insert a rounded
object to depress latch.
1
El pestillo se enganchará con la traba
cuando la puerta o gaveta se abra
5.08 cm (2 pulgadas). Para abrir la puerta
o gaveta, empuje el pestillo hacia abajo
con un dedo.
NOTA: Puede ser difícil acceder al pestillo
si lo utiliza en un cajón superior que tiene
un mostrador con un saliente de 1 pulg. Si
1"
To Install:
1. Attach enclosed positioning tape to mounting
surface of all pieces.
DO NOT
remove second
tape backing yet.
2. Position catch 1˝ from inside edge of cabinet
frame. Mark catch position. Remove positioning
tape backing and stick in position.
CAUTION:
Enclosed double-sided tape is for
positioning only. You must secure catch and latch
to cabinets and drawers with enclosed screws.
3. Position latch so it engages catch when door is
opened about 1.5˝. Mark latch position. Remove
positioning tape backing and stick in position.
Check alignment of catch and latch prior to
attaching with screws. After checking alignment,
secure both catch and latch tightly with screws.
To Use:
When drawer is opened 1.5˝ the latch will engage
catch. Press down on latch with finger to open.
NOTE:
An alternative method to mount these cabinet latches is to
mount the catch on the side of the cabinet and then mount the latch
sideways on the edge of the cabinet door or drawer.
CAUTION:
This product is only a deterrent. It is not a substitute for
proper adult supervision. Discontinue use when child becomes old
enough to defeat it. Toxic and dangerous substances, as well as
sharp-edged or pointed objects, should always be placed “high up”
or made otherwise inaccessible to small children.
NOTE:
Latch may be difficult to access if used on a top drawer that
has a counter top with a 1" overhang. If latch is difficult to access,
insert a rounded object to depress latch.
Cabinet & Drawer Latches
1"
To Install:
1. Attach enclosed positioning tape to mounting
surface of all pieces.
DO NOT
remove second
tape backing yet.
2. Position catch 1˝ from inside edge of cabinet
frame. Mark catch position. Remove positioning
tape backing and stick in position.
CAUTION:
Enclosed double-sided tape is for
positioning only. You must secure catch and latch
to cabinets and drawers with enclosed screws.
3. Position latch so it engages catch when door is
opened about 1.5˝. Mark latch position. Remove
positioning tape backing and stick in position.
Check alignment of catch and latch prior to
attaching with screws. After checking alignment,
secure both catch and latch tightly with screws.
To Use:
When drawer is opened 1.5˝ the latch will engage
catch. Press down on latch with finger to open.
NOTE:
An alternative method to mount these cabinet latches is to
mount the catch on the side of the cabinet and then mount the latch
sideways on the edge of the cabinet door or drawer.
CAUTION:
This product is only a deterrent. It is not a substitute for
proper adult supervision. Discontinue use when child becomes old
enough to defeat it. Toxic and dangerous substances, as well as
sharp-edged or pointed objects, should always be placed “high up”
or made otherwise inaccessible to small children.
NOTE:
Latch may be difficult to access if used on a top drawer that
has a counter top with a 1" overhang. If latch is difficult to access,
insert a rounded object to depress latch.
Cabinet & Drawer Latches
1
2
1. Line up catch to the front edge of
the door/drawer opening.
2. Mark the hole locations.
3. Cut out installation template from
instructions.
4. Punch out hole locations.
5. Tape template to cabinet lining
up dotted line with top edge of
cabinet opening.
6. Close cabinet door/drawer.
7. Mark top edge of door/drawer on
the template. Also mark the width
of the template on the door/drawer.
8. Open door/drawer. Remove
template from base of cabient and
retape onto the inside of the
door/drawer.
9. Position the template onto the
inside of the door/drawer lining up
the pencil marks.
10. Mark hole locations.
11. Predrill holes with X” drill bit.
Fron
t edge of cabinet opening
Front edge of cabinet opening
Front edge of cabinet opening
Front edge of cabinet opening
2
Catch:
1
Line up catch to the front edge of the cabinet
opening.
2
Mark the hole locations and the outer edges of the
catch on the cabinet opening (Figure 1).
3
Predrill holes with a 1/16” (1.5mm) drill bit.
4
Secure catch tightly with screws.
Enganche:
1
Alinee el enganche hasta el borde delantero de la
abertura del armario.
2
Marque las ubicaciones de los agujeros y los bordes
exteriores del enganche en la abertura del armario
(Figura 1).
3
Perfore los orificios con una broca de 1/16” (1.5 mm).
4
Fije firmemente el enganche con los tornillos.
Latch may be difficult to access if used on a top drawer that has a
countertop with a 1” overhang. If latch is difficult to access, insert a
rounded object to depress latch.
es difícil acceder al pestillo, inserte un objeto redondo para presionarlo.
El pestillo puede ser de difícil acceso si se utiliza en un cajón superior
que tiene una encimera con un 1’’ que sobresale. Si el pestillo es de difícil
acceso, inserte un objeto redondo para apretar el pestillo.
