background image

 

 

Return to Table of Contents

 

Ref: Crimping_Tool_18v_Handbook 

 

Page 9 of 16 

 

Doc ID: MKT-567      Version: 2.0    

 

CRIMPING TOOL - 18V BATTERY & CHARGER SET 

 
 

HOW TO OPERATE/USE CH-07 CHARGER 

 

 

The charger CH-07 is suitable for Li-Ion battery B-04(3Ah) & B-06(1.5Ah). The voltage of charger CH-
07 is 18V. 

 

 

 

While connecting to power, the digital monitor shows 

. The Buzzer buzzes once. 

 

Already connected to power, but the battery is not in the charger, the digital monitor shows 

 

and flash once a second.  

 

After inserting the battery in the charger, it will detect the battery voltage and show the capacity in 
percentages. 

 

If the battery is well charged, the digital monitor shows 

. The Buzzer buzzes once every three 

seconds. 

 

If the voltage of battery is low, the digital monitor shows 

. If the Buzzer buzzes once every 

second, it indicates the battery  has error/defect. 

 

If the temperature of the battery is high the digital monitor shows 

. The Buzzer buzzes once a 

second, wait until the battery is cooled down, then charge the battery. 

 

After charging for 10 Minutes, the voltage is not rising, the digital monitor shows 

. The Buzzer 

buzzes once every two seconds and stop one second, it means the battery has error/defect. 

 

The Max. Charging Time is 60-70 Minutes. After 70 Minutes, no matter if the battery is fully charged 
or not. The charger will stop.  

 

While charging, the digital monitor shows the capacity in percentage each 5% until 90%. After 90% 
of capacity, it will show the capacity in percentage each 1% until full charged, i.e. 100%. 

 

There is a protecting system that while the battery is full charged, it will stop charging automatically. 
And if the battery temperature is over 65 degree, it will stop charging automatically, too. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Digital 
Monitor 

Insert smoothly 
 

Summary of Contents for EPB-4201

















Reviews: