background image

19

EN

PROBLEM POSSIBLE CAUSE

WHAT TO DO

Machine does 

not heat up. 
STEAM/HOT 

WATER light 

flashes when 

the machine 

is turned on.

•  STEAM / HOT WATER dial is not in 

the STANDBY position. 

•  Turn the STEAM / HOT WATER dial to the STANDBY 

position. Machine will commence heating.

Water does 

not flow 

from the 

group head.
No hot water.

•  Machine has not reached operating 

temperature.

•  Allow time for the machine to reach operating 

temperature. The POWER button light will stop flashing 

and all button lights on the control panel  

will illuminate when ready.

•  Water tank is empty. 

•  Fill tank.

•  Water tank is not fully inserted  

and locked into position.

•  Push water tank down completely to lock into place.

•  Machine needs to be descaled.

•  Refer to ‘Descaling’, page 15.

•  Coffee is ground too finely and/or 

 too much coffee in filter basket and/ 

or over tamping and/or filter basket  

is blocked.

•  See below, ‘Espresso only drips from the portafilter 

spouts or not at all’.

Espresso only 

drips from 

the portafilter 

spouts or 

not at all.

•  Coffee is ground too finely.

•  Use slightly coarser grind. Refer to ‘Setting the  

Grind Size’, page 9 and ‘Over Extraction’, page 11.

•  Too much coffee in the filter basket.

•  Lower dose of coffee. Refer to ‘Setting the Grind 

Amount’, page 9 and ‘Over Extraction’, page 11.

•  Coffee tamped too firmly.

•  Tamp between 15–20kg of pressure.

•  Water tank is empty.

•  Fill tank.

•  Water tank is not fully inserted and 

locked into position.

•  Push water tank down completely to lock into place.

•  The filter basket may be blocked.

•  Use the pin on the end of the provided cleaning tool 

to unblock the hole(s). If the hole(s) remain blocked, 

dissolve a cleaning tablet in hot water and soak filter 

basket and portafilter in solution for approx.  

20 minutes. Rinse thoroughly.

•  Machine needs to be descaled.

•  Refer to ‘Descaling’, page 15.

Espresso 

runs out too 

quickly.

•  Coffee is ground too coarsely.

•  Use slightly finer grind. Refer to ‘Setting the Grind Size’, 

page 9 and ‘Under Extraction’, page 11.

•  Not enough coffee in the filter 

basket.

•  Increase dose of coffee. Refer to ‘Setting the Grind 

Amount’, page 9 and ‘Under Extraction’, page 11. 

•  Coffee tamped too lightly.

•  Tamp between 15–20kg of pressure.

Troubleshooting

Summary of Contents for Barista Express BES875



















Reviews: