background image

8

WARNING

Appliance surfaces will be hot 

during and after operation. 

8.  Clean the milk jug and frothing disc 

immediately after use. Refer to Care  

& Cleaning.

NOTE

When frothing multiple batches, to prevent 

the Boil Dry Protection from activating, we 

recommend allowing the milk jug to cool 

for approximately 5 minutes, or filling the 

milk jug with water for faster cooling. 

USING THE ‘COLD STIR’ SETTING 

The ‘Cold Stir’ setting allows you to stir already 

cold or hot milk without additional heat.
Use it to froth milk for cold beverages such as 

an iced cappuccino; to blend in syrups and 

flavourings for an iced chocolate or mocha;  

or to stir in dissolvable instant drinking powders 

into milk or water.

NOTE

The milk frother has been designed 

specifically for the purpose of foaming milk 

and other dairy milk alternatives and is 

not intended to whip, thicken or heat other 

food substances eg. oil, eggs, butter, heavy 

whipping cream, soups, gravies etc.
The milk frother is not designed to mix a 

large quantity of dry ingredients or melt large 

food pieces eg. cubed chocolate, ground 

nuts, whole spices, fresh herbs or ice cubes.

ADDING INGREDIENTS

Always allow the milk frother to start for  

a few seconds before using the measuring  

cap to gradually add ingredients.
Always add ingredients slowly and in small 

quantities. 

NOTE

Frothing results differ depending on the 

ingredients used. For example, adding 

dense ingredients like thick syrups, heavy 

powders and large flakes can significantly 

reduce the amount of foam.

SAFETY FEATURES

Boil Dry, Overheating Protection
The milk frother will automatically cease to 

operate if the milk jug overheats. This can 

be caused if the milk jug is empty, if liquid is 

below the MIN measurement marking, or after 

consecutive uses. If this occurs, 3 alerts will 

sound. Unplug the power cord from the power 

outlet, wait approximately 5 minutes for the milk 

frother to cool down or fill the milk jug with water 

for faster cooling.
Thermal Fuse & Current Protection
This feature protects the milk frother in case  

of major fault. If this occurs, the milk frother  

will automatically turn off and will not reactivate. 

Immediately cease use, remove the power  

plug from the power outlet and visit  

www.sageappliances.com or call  

Sage Consumer Service.

OPERATING YOUR SAGE

®

 MILK CAFÉ

Summary of Contents for Milk Cafe BMF600








Reviews: