background image

 

 

Safety and Certifications

 

 

 

25xxxxxxx-A 

17 July 2014 

 

 
Federal Communications Commission (FCC) Statements 

This device complies with Part 15 of the FCC Rules.  Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference, and  
(2)  This  device must accept  any  interference  received,  including  interference that may cause undesired 
operation. 

 

Label 

 

 

 
 
 

Modifications: 

You  are  cautioned  that  changes  or  modifications  not  expressly  approved  by  the  party  responsible  for 
compliance could void your authority to operate the equipment. 
 
FCC Responsible Party: 

Sagemcom USA 
14651 N. Dallas Parkway 
Suite 900 
Dallas, TX 75254 
Phone: 972-674-4100 

 
 

Radio Frequency Interference Statement 

Note:  This  equipment  has  been  tested  and  found  to  comply  with  the  limits  for  a  Class  B  digital  device, 
pursuant to Part 15 of the FCC Rules.  These limits are designed to provide reasonable protection against 
harmful  interference  in  a  residential  installation.   This  equipment  generates,  uses and can  radiate radio 
frequency  energy  and,  if  not  installed  and  used  in  accordance  with the  instructions, may cause harmful 
interference to radio communications.  However, there is no guarantee that interference will not occur in a 
particular installation.  If this equipment does cause harmful interference to radio or television reception, 
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures: 
 
1. Reorient or relocate the receiving antenna. 
2. Increase the separation between the equipment and receiver. 

Summary of Contents for F@ST 3284u












Reviews: