background image

 

sure it is positioned correctly so it does not obstruct any 
seatbelts. 

Fastening seatbelts 

 

Procedure: 

1.  Start by releasing all buckles (shoulder harness, crotch 

belts and waist belts). 

2.  Fasten the shoulder harness to the crotch belt and place 

the shoulder harness forward of the seat. 

3.  Place the child on the seat such that the crotch belt is 

between the child’s legs. 

4.  Move the buckles on the seat-back until they are just above 

the shoulders of the child. 

5. 

Lift the shoulder harness over the child’s chest and adjust 
the crotch belt so that its crotch 

buckle is on the child’s 

lower chest region. 

6.  If the shoulder harness is equipped with adjustment loops, 

adjust the shoulder harness straps until both straps are in 
the loops aligned with the top of the child’s shoulders. 
(When using lower loops. the upper portion of the shoulder 
harness 

has to be bent and inserted behind the child’s 

shoulder 

– reference provided pictures).  

7.  Fasten the two upper buckles of the shoulder harness into 

their corresponding buckles on the seat back. 

8.  Adjust the crotch belt and shoulder harness to become tight 

over the child’s chest. 

9.  Fasten and adjust the waist belt. When the waist belt is 

tight, the buckles must meet in the centre in front of the 
crotch belt. 

 

Warning:  

-

 

When one child is seated in the carrier, the child must be 
seated in the centre of the seat.  

-

 

Before each use, inspect all buckles and make sure all belts 
are threaded properly through the buckles.  

-

 

Before each use, make sure the seatbelts are correctly 
fastened around your child and are correctly adjusted to the 
size of your child.  

2.7

 

Climate Control 

Weather cover 

Your carrier is equipped with a three weather covers.  

 

-

 

The transparent cover is held by zippers on the sides. It can 
be rolled up and secured in the elastic loop at the top. 

-

 

The mesh cover is held in place by velcro tape at the lower 
end. The cover can be rolled up and secured in the elastic 
loop at the top. 

-

 

The short cover can be stretched forward and held by the 
velcro tapes on the sides of the carrier to function as a 

Summary of Contents for Fox 1

















Reviews: