13
ENGLISH
display is showing the correct color of the side to move.
Change the color, if necessary, by pressing BLACK/
>
or
WHITE/
<
.
•To exit Position Mode, press CLEAR. You will return to
normal game play, with your new board position.
Note that any legal position can be set up using the above
procedures. The computer will not permit you to set up an
illegal position, such as one where there are more than the
prescribed number of pieces for a normal game, or one
where a King is in check and is not to move. In such cases,
the computer will simply beep when you press
CLEAR
, and
you will not be allowed to exit Position Mode. Check the
position using the
PIECE SYMBOL KEYS
, if necessary, and
correct the position (by adding a piece, removing a piece, or
moving an incorrectly placed piece). Then press
CLEAR
to
exit Position Mode.
9. TECHNICAL DETAILS
9.1 The ACL Function
Computers sometimes “lock up” due to static discharge or
other electrical disturbances. If this should happen, take out
the batteries and use a pin or another sharp object to press
into the hole marked ACL in the base of the unit for at least
one second. This resets the computer.
9.2 Care and Maintenance
Your chess computer is a precision electronic device, and
should not be subjected to rough handling or exposed to
extreme temperatures or moisture. Be sure to disconnect the
adapter (if applicable) and remove the batteries before clean-
ing the unit. Do not use chemical agents or liquids to clean
the unit, as they may damage the plastic.
Weak batteries should be replaced promptly, since they can
leak and damage the computer. Please also note the follow-
ing regarding the use of batteries.
Warning: Use only alka-
line or zinc carbon batteries. Do not mix different types
of batteries or new and used batteries. Do not recharge
non-rechargeable batteries. Use only the recommended
batteries or equivalent. Be sure to observe the correct
polarity when inserting batteries. Worn out batteries
should be removed from the unit promptly. Do not short
circuit the supply terminals.
If an AC-DC adapter is used with this unit, it must be as
specified in Section 9.3. An adapter is not a toy and should
be handled with care. Please also note the following regard-
ing the use of an AC-DC adapter.
Warning: Use a center
positive adapter with safety isolating transformer. The
polarity symbols confirming its center positivity should
be clearly marked on the adapter, and the adapter must
comply with EN60742. The adapter should be regularly
examined for potential hazards such as damage to the
plug, cable or cord, casing or other parts. In the event of
damage, the adapter should not be used.
9.3 Technical Specifications
Keys:
17
LCD Display:
48-segment, 5-digit
Batteries:
4 x AA batteries
Power Consumption: 330 mW maximum
Dimensions:
335 x 302 x 35 mm
Weight:
1 kg (without batteries)
AC-DC Adapter:
9V/300mA center-positive
Please retain this information for future reference.
Saitek reserves the right to make technical changes without notice in the
interest of progress.
CONDITIONS OF WARRANTY
1. Warranty period is 2 years from date of purchase with proof of
purchase submitted.
2. Operating instructions must be followed.
3. Product must not have been damaged as a
result of defacement, misuse, abuse, neglect,
accident, destruction or alteration of the serial
number, improper electrical voltages or cur-
rents, repair, alteration or maintenance by any
person or party other than our own service facility or
an authorized service center, use or installation of
non-Saitek replacement parts in the product or the modification of
this product in any way, or the incorporation of this product into
any other products, or damage to the product caused by accident,
fire, floods, lightning, or acts of God, or any use violative of in-
structions furnished by Saitek plc.
4. Obligations of Saitek shall be limited to repair or replacement with
the same or similar unit, at our option. To obtain repairs under this
warranty, present the product and proof of purchase (e.g., bill or
invoice) to the authorized Saitek Technical Support Center (listed
on the separate sheet packaged with this product) transportation
charges prepaid. Any requirements that conflict with any state or
Federal laws, rules and/or obligations shall not be enforceable in
that particular territory and Saitek will adhere to those laws, rules,
and/or obligations.
5. When returning the product for repair, please pack it very carefully,
preferably using the original packaging materials. Please also
include an explanatory note.
6. IMPORTANT: To save yourself unnecessary cost and inconve-
nience, please check carefully that you have read and followed the
instructions in this manual.
7. This warranty is in Lieu of all other expressed warranties, obliga-
tions or liabilities. ANY IMPLIED WARRANTIES, OBLIGATIONS,
OR LIABILITIES, INCLUDING BUT NOT LIMITED TO THE IM-
PLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, SHALL BE LIMITED IN DURA-
TION TO THE DURATION OF THIS WRITTEN LIMITED WAR-
RANTY. Some states do not allow limitations on how long an
implied warranty lasts, so the above limitations may not apply to
you. IN NO EVENT SHALL WE BE LIABLE FOR ANY SPECIAL
OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR
ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSO-
EVER Some states do not allow the exclusion or limitation of
special, incidental or consequential damages, so the above limita-
tion may not apply to you. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to
state.
Information for Customers in the United States:
FCC Compliance and Advisory Statement
Warning: Changes or modifications to this unit not expressly ap-
proved by the party responsible for compliance could void the user’s
authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equip-
ment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installa-
tion. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Saitek Industries, 2295 Jefferson Street, Torrance, CA 90501, USA
