background image

1 6  

P  R  O   P  E  L  L  E  R    S  E  L  E  C   T   I  O  N

Propeller Selection

In the chart below you will find a
propeller selection list. This chart will
enable you to select the best propeller
for initial setup of your Saito engine.

Remember, it is imperative to balance

each propeller prior to installation
onto your Saito engine. Failure to do
so may cause unwanted vibration in
your aircraft.

Figure 5

Saito Single-Cylinder Propeller Chart

NOTE: All recommendations are based on engines using APC props, Power Master 15% 
2-stroke fuel, and McCoy MC-4C glow plugs.

ENGINE

SPORT

SCALE

AEROBATICS

FA-30S (H)/30SGK

2,200

– 

12,000 rpm

10 x 5

10 x 5, 10 x 6

9 x 6, 10 x 5 

FA-50/50GK

2000

– 

12,000 rpm

11 x 7, 11 x 8, 12 x 6

12 x 5, 12 x 6

11 x 7, 11 x 8, 12 x 6

FA-56/56GK

2000

– 

12,000 rpm

11 x 8, 12 x 6, 12 x 7

12 x 6, 12 x 7

11 x 8, 12 x 6, 12 x 4

FA-65/65GK

2000

– 

11,500 rpm

12 x 6, 12 x 8, 13 x 8

13 x 8, 14 x 5, 14 x 6

11 x 9, 12 x 8, 13 x 6

FA-72/72GK

2000

– 

11,500 rpm

12 x 8, 13 x 6, 13 x 8, 

13 x 6, 13 x 8, 14 x 6, 

11 x 9, 11 x 10,12 x 8, 

14 x 6

15 x 4

12 x 9

FA-80/80GK

2000

– 

11,500 rpm

12 x 8, 13 x 6, 13 x 8, 

13 x 6, 13 x 8, 14 x 6, 

11 x 9, 11 x 10,12 x 8, 

14 x 6

15 x 4

12 x 9

FA-91S/91SGK

2000

– 

11,000 rpm

12 x 8, 13 x 7,13 x 8,

13 x 7, 13 x 8, 14 x 5

11 x 10, 11 x 11, 12 x 9

14 x 6, 14 x 8

14 x 6, 15 x 4

12 x 10N, 13 x 9

FA-120S/120SGK

2000

– 

11,000 rpm

14 x 10,15 x 8, 15 x 10

15 x 8, 16 x 6, 16 x 8,

13.5 x 13.5, 14 x 10N

16 x 16, 16 x 8

18 x 6

14 x 12

FA-150/150GK

2000

– 

10,500 rpm

15 x 8, 15 x 10, 16 x 8

16 x 8, 18 x 6, 18 x 8,

14 x 10N, 14 x 14, 

18 x 6, 18 x 8

15 x 10, 15 x 11

FA-180/180GK

2000

– 

11,000 rpm

15 x 8, 15 x 10, 15 x 11

16 x 8, 16 x 10, 

14 x 13.5, 

16 x 8, 16 x 10

18 x 6

15 x 12

NOTE: Observe operating rpm ranges as excessive rpm can result in damage to the engine.

You will note a letter (A, B,C, etc.) stamped on the top of the motor mount. This letter

identifies the production version of your engine. Should you ever need to order a part or have a
question pertaining to your engine, specify this letter along with the engine type. This will
allow for easier identification of your engine.

 Saito Single Cyl Manual 9-00  9/11/00  10:06 AM  Page 18

Summary of Contents for FA-30S (H)

























Reviews: